Stihl MS 251 Instruction Manual - Page 77

Choke Rod, 10.3.4 Throttle Rod, Remove the choke rod

Get Stihl MS 251 PDF manuals and user guides View all Stihl MS 251 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

10.3.3 Choke Rod - Remove the air filter, b 12.1 1 1 32 2310RA198 TG 2310RA194 TG 2 : Position the choke rod (1) in the : Pull the filter base (1) off the 1 guide (arrow). studs (arrows). 2310RA192 TG : Set the switch lever (1) to "F" and ease the choke rod (2) out of its seat (arrow). : Disconnect the choke rod (2) from the lever (3). - Check the choke rod and replace it if necessary Installing : Set the switch lever (2) to "F", hold it in that position and then push the choke rod (1) fully into its seat (arrow). - Check operation Check that the choke rod is properly seated. - Reassemble all other parts in the reverse sequence. 10.3.4 Throttle Rod 1 2 : Pull the filter base (1) out of the buffer (2). 2 - Remove the throttle trigger, b 10.2, QuickStop Super, b 10.3 2310RA197 TG 1 : Engage the choke rod (1) in the bore (arrow) in the choke shaft (2). 2310RA193 TG - Remove the choke rod, b 10.3.3 - Remove the baffle, b 12.2 1 2 1 2310RA196 TG : Pull the short circuit wire (1) and ground wire (2) out of the guides (arrows). - Put the filter base to one side so that the wires are not under tension. 2310RA195 TG 2 : Pry the filter base (1) out of the buffer (2). 76 MS 231, MS 231 C, MS 251, MS 251 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
76
MS 231, MS 231 C, MS 251, MS 251 C
10.3.3
Choke Rod
–
Remove the air filter,
b
12.1
:
Set the switch lever (1) to "
F
" and
ease the choke rod (2) out of its
seat (arrow).
:
Disconnect the choke rod (2)
from the lever (3).
–
Check the choke rod and replace
it if necessary
Installing
:
Engage the choke rod (1) in the
bore (arrow) in the choke
shaft (2).
3
2310RA192 TG
1
2
2
2310RA193 TG
1
:
Position the choke rod (1) in the
guide (arrow).
:
Set the switch lever (2) to "
F
",
hold it in that position and then
push the choke rod (1) fully into
its seat (arrow).
–
Check operation
Check that the choke rod is properly
seated.
–
Reassemble all other parts in the
reverse sequence.
10.3.4
Throttle Rod
–
Remove the throttle trigger,
b
10.2,
QuickStop Super,
b
10.3
–
Remove the choke rod,
b
10.3.3
–
Remove the baffle,
b
12.2
:
Pry the filter base (1) out of the
buffer (2).
2310RA194 TG
2
1
2
2310RA195 TG
1
:
Pull the filter base (1) off the
studs (arrows).
:
Pull the filter base (1) out of the
buffer (2).
:
Pull the short circuit wire (1) and
ground wire (2) out of the
guides (arrows).
–
Put the filter base to one side so
that the wires are not under
tension.
2310RA198 TG
1
2
2310RA197 TG
1
2
2310RA196 TG
1