Compaq ProLiant 8500 Compaq ProLiant 8500 Setup and Installation Guide - Page 64

Opening the Processor and Memory Module

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Server Operation 3-9 5. Set the module aside for servicing non hot-plug components. WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. CAUTION: Never operate the server for extended periods of time, with an access panel or module removed or partially installed. Doing so will cause thermal damage to the system and could void your warranty. 6. To view the top panel labels, pull the chassis out of the rack until it makes contact with the rail stop. NOTE: These top panel labels provide instructions on installing expansion boards, setting switches, and installing Hot Plug fans, as well as information on PCI Hot Plug. See Chapter 4 "Installing Hardware Options" for Hot Plug procedures. 7. To reassemble the server, slide the module in until the ejectors begin to rotate. Then push ejectors shut until they snap into place. Opening the Processor and Memory Module CAUTION: Do not attempt to open any of the three modules while power is applied to the system. They are not hot pluggable. Immediate system shutdown and loss of data will occur. To open the Processor and Memory Module: 1. If the computer is on, place the computer in Standby mode. See Chapter 2, "Server Installation." 2. Push the sides of the latches 1 on the Processor and Memory Module in and rotate the top of the levers downward 2 as shown in the following figure. 3. Pull the Processor and Memory Module out of the chassis until it encounters the module stop latch. 4. At this point you can remove the memory board to add or replace memory modules as described in Chapter 4, "Installing Hardware Options."

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Server Operation
3-9
5.
Set the module aside for servicing non hot-plug components.
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the
internal system components to cool before touching them.
CAUTION:
Never operate the server for extended periods of time, with an
access panel or module removed or partially installed. Doing so will cause
thermal damage to the system and could void your warranty.
6.
To view the top panel labels, pull the chassis out of the rack until it
makes contact with the rail stop.
NOTE:
These top panel labels provide instructions on installing expansion boards, setting
switches, and installing Hot Plug fans, as well as information on PCI Hot Plug. See
Chapter 4 “Installing Hardware Options” for Hot Plug procedures.
7.
To reassemble the server, slide the module in until the ejectors begin to
rotate. Then push ejectors shut until they snap into place.
Opening the Processor and Memory Module
CAUTION:
Do not attempt to open any of the three modules while power is
applied to the system. They are not hot pluggable. Immediate system shutdown
and loss of data will occur.
To open the Processor and Memory Module:
1.
If the computer is on, place the computer in Standby mode. See
Chapter 2, “Server Installation.”
2.
Push the sides of the latches
1
on the Processor and Memory Module in
and rotate the top of the levers downward
2
as shown in the following
figure.
3.
Pull the Processor and Memory Module out of the chassis until it
encounters the module stop latch.
4.
At this point you can remove the memory board to add or replace
memory modules as described in Chapter 4,
“Installing Hardware
Options.”