Compaq ProLiant 8500 Compaq ProLiant 8500 Setup and Installation Guide - Page 83

as shown in the following

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Installing Hardware Options 4-15 3. Remove the memory board by rotating the ejectors outward 1 and pulling the board out 2. 4. Place the memory expansion board, components facing up, on a flat surface. 1 1 2 Figure 4-14. Removing the memory board NOTE: The memory board is part of the system interconnect scheme and must be seated properly for server start up. For more information see the "System Interconnect Status Indicators" section in Chapter 3, "Server Operation." CAUTION: The ejectors prevent the memory expansion board from lying completely flat. Inserting a DIMM without counter pressure applied behind the socket to the back of the expansion board can cause the memory expansion board to flex and could result in damage. Always support the memory expansion board or apply counter pressure while inserting a DIMM. 5. Open the DIMM socket latches 1 as shown in the following figure. 6. Align the key slot on the bottom edge of each DIMM with the tab in the DIMM socket.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Installing Hardware Options
4-15
3.
Remove the memory board by rotating the ejectors outward
1
and
pulling the board out
2
.
4.
Place the memory expansion board, components facing up, on a flat
surface.
1
1
2
Figure 4-14.
Removing the memory board
NOTE:
The memory board is part of the system interconnect scheme and must be seated
properly for server start up. For more information see the “System Interconnect Status
Indicators” section in Chapter 3, “Server Operation.”
CAUTION:
The ejectors prevent the memory expansion board from lying
completely flat. Inserting a DIMM without counter pressure applied behind the
socket to the back of the expansion board can cause the memory expansion
board to flex and could result in damage. Always support the memory expansion
board or apply counter pressure while inserting a DIMM.
5.
Open the DIMM socket latches
1
as shown in the following figure.
6.
Align the key slot on the bottom edge of each DIMM with the tab in the
DIMM socket.