Compaq ProLiant 8500 Compaq ProLiant 8500 Setup and Installation Guide - Page 76

Table 4-2, Processor Bus/Core Ratio Switch Settings, Processor Frequency, Bus/Core, Ratio

Get Compaq ProLiant 8500 PDF manuals and user guides View all Compaq ProLiant 8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

4-8 Compaq ProLiant 8500 Servers Setup and Installation Guide 4. Rotate the ejector levers 1 fully to unseat the processor terminator board from the socket. Remove the processor terminator board by pulling it out by the handle 2. Retain for future use. NOTE: If you remove a Pentium III Xeon processor, the processor terminator board must be re-installed before powering up the server. 2 1 1 Figure 4-8. Removing the processor terminator board 5. Remove the memory board for easier access to the processor bus/core ratio switch. 6. Locate the processor bus/core ratio switch for the processor bus that will receive the new processor. See Table 4-2 or the panel label. 7. Set the processor bus/core ratio switch to the appropriate setting. Table 4-2 Processor Bus/Core Ratio Switch Settings Processor Frequency Bus/Core 1 2 3 4 Ratio 450-MHz models 4 1/2 OFF ON OFF ON 500-MHz models 5 ON OFF OFF ON 550-MHz models 5 1/2 OFF OFF OFF ON Auto Configuration (Default) 2 OFF OFF OFF OFF Note: This table indicates the capabilities of the server hardware. It does not mean to imply that processors are available to match each of the settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
4-8
Compaq ProLiant 8500 Servers Setup and Installation Guide
4.
Rotate the ejector levers
1
fully to unseat the processor terminator
board from the socket. Remove the processor terminator board by
pulling it out by the handle
2
. Retain for future use.
NOTE:
If you remove a Pentium III Xeon processor, the processor terminator board must
be re-installed before powering up the server.
2
1
1
Figure 4-8.
Removing the processor terminator board
5.
Remove the memory board for easier access to the processor bus/core
ratio switch.
6.
Locate the processor bus/core ratio switch for the processor bus that will
receive the new processor. See Table 4-2 or the panel label.
7.
Set the processor bus/core ratio switch to the appropriate setting.
Table 4-2
Processor Bus/Core Ratio Switch Settings
Processor Frequency
Bus/Core
Ratio
1
2
3
4
450-MHz models
4 1/2
OFF
ON
OFF
ON
500-MHz models
5
ON
OFF
OFF
ON
550-MHz models
5 1/2
OFF
OFF
OFF
ON
Auto Configuration (Default)
2
OFF
OFF
OFF
OFF
Note:
This table indicates the capabilities of the server hardware. It does not mean to
imply that processors are available to match each of the settings.