Dell Inspiron 7000 Dell Inspiron 7000 Service Manual - Page 77

Gently pull the interposer board off the connector to the LCD panel.

Get Dell Inspiron 7000 PDF manuals and user guides View all Dell Inspiron 7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

6. Remove the hinges, which were previously held in place by pressure and screws. To remove the LCD brackets from the LCD panel, follow these steps: 1. Remove the four 4-mm screws from the sides of the LCD brackets. 2. Remove the brackets from the LCD panel. To remove the LCD panel from the carrier tray, follow these steps: 1. Lift the inverter board shield, pull it slightly away from the panel to expose the cabling, and detach the LCD wire harness from connector CN1 on the inverter board. 2. Remove any Kapton tape covering the CCFL cable on the back of the LCD. 3. Gently pull the interposer board off the connector to the LCD panel. 4. Lift the LCD panel up and remove any tape between the LCD wire harness and the carrier tray. 5. Disconnect the LCD wire harness from the LCD panel. 6. Lift the LCD panel out of the carrier tray. 7. Disconnect the LCD wire harness from the LCD panel. Removing and Replacing Parts 4-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Removing and Replacing Parts
4-43
6.
Remove the hinges, which were previously held in place by pressure and
screws.
To remove the LCD brackets from the LCD panel, follow these steps:
1.
Remove the four 4-mm screws from the sides of the LCD brackets.
2.
Remove the brackets from the LCD panel.
&$87,21±²7KH²PHWDO²RQ²WKH²FDUULHU²WUD\²LV²VKDUS³²%H²FDUHIXO²QRW²WR²FXW²
\RXUVHOI³
To remove the LCD panel from the carrier tray, follow these steps:
1.
Lift the inverter board shield, pull it slightly away from the panel to expose
the cabling, and detach the LCD wire harness from connector CN1 on the
inverter board.
2.
Remove any Kapton tape covering the CCFL cable on the back of the LCD.
3.
Gently pull the interposer board off the connector to the LCD panel.
4.
Lift the LCD panel up and remove any tape between the LCD wire harness
and the carrier tray.
5.
Disconnect the LCD wire harness from the LCD panel.
6.
Lift the LCD panel out of the carrier tray.
7.
Disconnect the LCD wire harness from the LCD panel.