Denon AVR 4806 Owners Manual - Page 25

Playing a DVD with Surround Sound, About the error message - reset

Get Denon AVR 4806 - AV Receiver PDF manuals and user guides
UPC - 081757506465
View all Denon AVR 4806 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

About the error message Easy Setup and Operation • These error messages will be displayed when performing the measurements of Auto Setup and the automatic measurements can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the pertinent items, and measure again. Be sure to turn off the AVR-4806's power before checking the speaker connections. Screen example Cause q The speakers required for producing suitable reproduction have not been detected. • The front L and front R speakers were not properly detected. • Only one channel of the surround (A) and surround (B) speakers was detected. • Sound was output from the R channel when only one surround back speaker was connected. • The surround back or the surround (B) speaker was detected, but the surround (A) speaker was not detected. If multiple errors occur, press the CURSOR F or G button to check the contents. w The speaker polarity is connected in reverse. If multiple errors occur, press the CURSOR F or G button to check the contents. Measures • Check that the pertinent speakers are properly connected. • Check the polarity of the pertinent speakers. • For some speakers, the screen below may be displayed even though the speakers are properly connected. If so, select "Skip0". e There is too much ambient noise in the room and the measurements cannot be made accurately. r The sound level that is output from the speakers and/or subwoofer is too low. t The measurement microphone is not connected, or all of speakers have not been detected. • Either turn off the power of the device that generated the noise during the measurements or move the device away. • Try again at a time when it is quieter. • Check the placement and orientation of the loudspeakers. • Adjust the subwoofer's output level. • Connect the measurement microphone to the microphone connector. • Check the speaker connection. Playing a DVD with Surround Sound 1 Disconnect the microphone from the unit. 2 Select the input source to be played. 3 Select the play mode. 4 Start DVD playback. 5 Adjust the volume. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
25
Easy Setup and Operation
Measures
Cause
Screen example
About the error message
•
These error messages will be displayed when performing the measurements of Auto Setup and the automatic measurements
can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the
following matters, reset the pertinent items, and measure again. Be sure to turn off the AVR-4806’s power before checking the
speaker connections.
q
The speakers required for producing suitable
reproduction have not been detected.
• The front L and front R speakers were not
properly detected.
• Only one channel of the surround (A) and
surround (B) speakers was detected.
• Sound was output from the R channel when
only
one
surround
back
speaker
was
connected.
•
The surround back or the surround (B) speaker
was detected, but the surround (A) speaker
was not detected.
If multiple errors occur, press the
CURSOR
F
or
G
button to check the contents.
• Check that the pertinent speakers
are properly connected.
w
The speaker polarity is connected in reverse.
If multiple errors occur, press the
CURSOR
F
or
G
button to check the contents.
• Check the polarity of the pertinent
speakers.
• For some speakers, the screen
below may be displayed even though
the speakers are properly connected.
If so, select “Skip
0
”.
e
There is too much ambient noise in the room
and the measurements cannot be made
accurately.
r
The sound level that is output from the
speakers and/or subwoofer is too low.
• Either turn off the power of the
device that generated the noise
during the measurements or move
the device away.
•
Try again at a time when it is quieter.
•
Check the placement and orientation
of the loudspeakers.
•
Adjust the subwoofer’s output level.
t
The
measurement
microphone
is
not
connected, or all of speakers have not been
detected.
•
Connect the measurement microphone
to the microphone connector.
•
Check the speaker connection.
Playing a DVD with Surround Sound
1
Disconnect the microphone from the unit.
2
Select the input source to be played.
3
Select the play mode.
4
5
Adjust the volume.
Start DVD playback.