Denon AVR 4806 Owners Manual - Page 92

Setting the IEEE1394 Assign, IEEE1394 Assign at the Audio Input

Get Denon AVR 4806 - AV Receiver PDF manuals and user guides
UPC - 081757506465
View all Denon AVR 4806 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Advanced Setup - Part 1 If you wish to set the input source back to as it was initially, press the CURSOR H button with the input source highlighted. If "Yes" is selected for "Default", the setting are automatically reset to the default name. Setting the IEEE1394 Assign • Assign the device connected by IEEE1394 cable to an input source. The power of the device to be assigned must be turned on ahead of time. 1 Press the CURSOR D or H button to select the "IEEE1394 Assign" at the "Audio Input Setup" menu, then press the ENTER button. • Display the "IEEE1394 Assign" screen. 5 Once all the characters have been input, press the ENTER button. • The "Function Rename" screen reappears. Use the same procedure to change other input source names as well. 6 Press the ENTER button to enter the setting. • The "Audio Input Setup" menu reappears. 2 Press the CURSOR D or H button to select the device to be assigned to the input source, then press the CURSOR F or G button to select the input source. • When the input source is selected, the display is as shown below. Example: When the name has been changed to "DVD5910" 3 Press the ENTER button to enter the setting. • The "Audio Input Setup" menu reappears. • If you do not wish to assign the device connected by IEEE1394 cable to an input source, the IEEE1394 input can be selected by turning the FUNCTION knob. In this case, the connection information is cleared when the power of the connected device or the AVR-4806 is turned off, so the selection procedure must be performed again. • By default, if no device has been connected using an IEEE1394 cable in the past, "No Connection" is displayed. • "Connection Change" is displayed if there is a change in the IEEE1394 connection status while this screen is displayed. • If the model name cannot be acquired from the connected IEEE1394 device, "UNKNOWN" is displayed. • If an IEEE1394 device other than one for IEEE1394 audio playback is connected, "Not Play" is displayed and the input source cannot be assigned. 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Advanced Setup – Part 1
92
If you wish to set the input source back to as it was
initially, press the
CURSOR
H
button with the input
source highlighted.
If “Yes” is selected for “Default”, the setting are
automatically reset to the default name.
5
Once all the characters have been input, press
the
ENTER
button.
•
The “Function Rename” screen reappears.
Use the same procedure to change other input source
names as well.
6
Press the
ENTER
button to enter the setting.
•
The “Audio Input Setup” menu reappears.
• When the input source is selected, the display is as shown
below.
Example:
When the name has been changed to “DVD-
5910”
• If you do not wish to assign the device connected by
IEEE1394 cable to an input source, the IEEE1394 input can
be selected by turning the
FUNCTION
knob. In this case, the
connection information is cleared when the power of the
connected device or the AVR-4806 is turned off, so the
selection procedure must be performed again.
• By default, if no device has been connected using an
IEEE1394 cable in the past, “No Connection” is displayed.
•
“Connection Change” is displayed if there is a change in the
IEEE1394 connection status while this screen is displayed.
• If the model name cannot be acquired from the connected
IEEE1394 device, “UNKNOWN” is displayed.
• If an IEEE1394 device other than one for IEEE1394 audio
playback is connected, “Not Play” is displayed and the input
source cannot be assigned.
Setting the IEEE1394 Assign
• Assign the device connected by IEEE1394 cable to an input
source. The power of the device to be assigned must be
turned on ahead of time.
1
Press the
CURSOR
D
or
H
button to select the
“IEEE1394 Assign” at the “Audio Input
Setup” menu, then press the
ENTER
button.
•
Display the “IEEE1394 Assign” screen.
2
Press the
CURSOR
D
or
H
button to select the
device to be assigned to the input source, then
press the
CURSOR
F
or
G
button to select the
input source.
3
Press the
ENTER
button to enter the setting.
•
The “Audio Input Setup” menu reappears.