HP 2600 HP Business Inkjet 2600/2600dn - (English) User's Guide - Page 104

Paper is not picked up from a tray, Paper is not picked up from the manual feed units

Get HP 2600 - Business Inkjet Color Printer PDF manuals and user guides View all HP 2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

8-22 Paper is not picked up from a tray ! The tray size or type settings configured in the LCD control panel do not match the size or type selected in the printer driver Make sure the correct media is loaded in the tray and that the media size and type are set correctly in the LCD control panel. For more information about setting media sizes and types, see "Load paper and configure media types and sizes." ! The paper width guide is pressed too tightly against the paper stack Check that the paper width guide is snug, but not tight, against the paper stack. ! Photo paper is curled If you are using photo paper, make sure it is not curled. Uncurl the paper by gently bending it in the opposite direction of the curl. ! The "Pick From Other Tray If Empty" setting is turned off If you want the printer to draw paper from the other tray if it runs out of paper, make sure the "Pick From Other Tray If Empty" setting is turned on and that the media type and size settings in the LCD control panel are the same for both trays. If this setting is turned off, the printer does not use paper from the other tray to complete the print job. Paper is not picked up from the manual feed units ! The paper width guide in the front manual feed is pressed too tightly against the paper stack Check that the paper width guide is snug, but not tight, against the paper stack. ! Too much media is loaded in the manual feed units The front manual feed is designed to hold up to 10 sheets of paper. The rear manual feed is designed to hold a single sheet of media. ! Paper is wrinkled or bent Make sure the paper is not wrinkled or bent. Remove media from the manual feed units after use. Leaving media in the manual feed units overnight can cause the media to bend. ! Paper in tray 1 is interfering with the front manual feed, causing more than one page to be fed Remove the media in tray 1. ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
8-22
ENWW
Paper is not picked up from a tray
!
The tray size or type settings configured in the LCD control
panel do not match the size or type selected in the printer
driver
Make sure the correct media is loaded in the tray and that the
media size and type are set correctly in the LCD control panel. For
more information about setting media sizes and types, see “Load
paper and configure media types and sizes.”
!
The paper width guide is pressed too tightly against the paper
stack
Check that the paper width guide is snug, but not tight, against the
paper stack.
!
Photo paper is curled
If you are using photo paper, make sure it is not curled. Uncurl the
paper by gently bending it in the opposite direction of the curl.
!
The “Pick From Other Tray If Empty” setting is turned off
If you want the printer to draw paper from the other tray if it runs out
of paper, make sure the “Pick From Other Tray If Empty” setting is
turned on and that the media type and size settings in the LCD
control panel are the same for both trays. If this setting is turned off,
the printer does not use paper from the other tray to complete the
print job.
Paper is not picked up from the manual feed units
!
The paper width guide in the front manual feed is pressed too
tightly against the paper stack
Check that the paper width guide is snug, but not tight, against the
paper stack.
!
Too much media is loaded in the manual feed units
The front manual feed is designed to hold up to 10 sheets of paper.
The rear manual feed is designed to hold a single sheet of media.
!
Paper is wrinkled or bent
Make sure the paper is not wrinkled or bent. Remove media from
the manual feed units after use. Leaving media in the manual feed
units overnight can cause the media to bend.
!
Paper in tray 1 is interfering with the front manual feed,
causing more than one page to be fed
Remove the media in tray 1.