HP ProLiant 4500 Compaq ProLiant Cluster HA/F100 and HA/F200 Administrator Gui - Page 86

Installing the Software, Assisted Integration Using SmartStart (Recommended), Recommended

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Setting Up the Compaq ProLiant Clusters HA/F100 and HA/F200 3-13 Installing the Software The following information describes the software installation steps for the HA/F100 and the HA/F200. Proceed with these steps once you have all equipment installed and your hubs, storage system, and one server powered up. You need the following during installation: IMPORTANT: Refer to Appendix C for the software and firmware version levels your cluster requires. s Compaq SmartStart for the Servers CD s Compaq SmartStart for Servers Setup Poster s Server Profile Diskette (included with SmartStart) s Microsoft Windows NT Server 4.0/Enterprise Edition software and documentation s Compaq Redundancy Manager (Fibre Channel) software s Monitoring and Management Software q Compaq Insight Manager software and documentation q Compaq Insight Manager XE software and documentation q Compaq Intelligent Cluster Administrator software and documentation s At least ten high-density diskettes s Windows NT 4.0 Service Packs Assisted Integration Using SmartStart (Recommended) Use the SmartStart Assisted Integration procedure to configure the servers (nodes) in the HA/F100 and HA/F200 configuration. You will set up two nodes during this process. Go through all steps on each of the nodes with noted exceptions. The following steps will take you through the SmartStart Assisted Integration procedure. CAUTION: Installation using SmartStart assumes that SmartStart is being installed on new servers. Any existing data on the servers' boot drive will be erased.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Setting Up the Compaq ProLiant Clusters HA/F100 and HA/F200
3-13
Installing the Software
The following information describes the software installation steps for the
HA/F100 and the HA/F200. Proceed with these steps once you have all
equipment installed and your hubs, storage system, and one server powered
up.
You need the following during installation:
IMPORTANT:
Refer to Appendix C for the software and firmware version levels your
cluster requires.
■
Compaq SmartStart for the Servers CD
■
Compaq SmartStart for Servers Setup Poster
■
Server Profile Diskette (included with SmartStart)
■
Microsoft Windows NT Server 4.0/Enterprise Edition software and
documentation
■
Compaq Redundancy Manager (Fibre Channel) software
■
Monitoring and Management Software
Compaq Insight Manager software and documentation
Compaq Insight Manager XE software and documentation
Compaq Intelligent Cluster Administrator software and
documentation
■
At least ten high-density diskettes
■
Windows NT 4.0 Service Packs
Assisted Integration Using SmartStart
(Recommended)
Use the SmartStart Assisted Integration procedure to configure the servers
(nodes) in the HA/F100 and HA/F200 configuration. You will set up two
nodes during this process. Go through all steps on each of the nodes with
noted exceptions. The following steps will take you through the SmartStart
Assisted Integration procedure.
CAUTION:
Installation using SmartStart assumes that SmartStart is being
installed on new servers. Any existing data on the servers’ boot drive will be
erased.