HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 28

Attach the rear mounting brackets to the rear rack uprights by completing one

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Installing the SAN Switch 2/32 Table 4: Rack Mount Kit rails and rail mounting hardware (Continued) Item Description (8) #10 adapter washer (2) 1/4-20 hex nut with captive star lock washer (2) 1/4-inch flat washer Caution: For proper air flow, the SFP media side of the SAN Switch 2/32 must face the rear of the rack. This mounting allows air to enter from the front of the rack and to exhaust at the rear of the rack, similar to other rack-mounted equipment. This prevents switch overheating, which may cause it to fail. To install the switch in a rack: 1. Check the contents of the shipping carton to verify that all the required parts and hardware are available. 2. Choose a mounting location in the rack for the switch. 3. Attach the rear mounting brackets to the rear rack uprights by completing one of the following steps: - For an HP 10000 series or comparable EIA cabinet, assemble each of the two brackets with two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 adapter washers as shown in Figure 4. 28 SAN Switch 2/32 Version 4.2.x Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
28
SAN Switch 2/32 Version 4.2.x Installation Guide
Caution:
For proper air flow, the SFP media side of the SAN Switch 2/32
must face the rear of the rack. This mounting allows air to enter from the front
of the rack and to exhaust at the rear of the rack, similar to other rack-mounted
equipment. This prevents switch overheating, which may cause it to fail.
To install the switch in a rack:
1.
Check the contents of the shipping carton to verify that all the required parts
and hardware are available.
2.
Choose a mounting location in the rack for the switch.
3.
Attach the rear mounting brackets to the rear rack uprights by completing one
of the following steps:
—
For an HP 10000 series or comparable EIA cabinet, assemble each of the
two brackets with two #10-32 x 1/2-inch Phillips pan-head screws with
captive star lock washers and two #10 adapter washers as shown in
Figure 4
.
(8) #10 adapter washer
(2) 1/4-20 hex nut with captive star lock
washer
(2) 1/4-inch flat washer
Table 4:
Rack Mount Kit rails and rail mounting hardware (Continued)
Item
Description