HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 38

Connecting AC Power, Attach the remaining ends of the power cords to power outlets.

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Installing the SAN Switch 2/32 Connecting AC Power Follow these steps to power on the SAN Switch 2/32. Caution: Do not plug the power cords into the power source until the switch is completely installed in the rack. 1. Connect the SAN Switch 2/32 power cords to the power connectors on the switch as shown in Figure 13. Figure 13: Connecting the power cords SHR-2571A 2. Attach the remaining ends of the power cords to power outlets. 3. Turn on the power switch (the 1 position indicates power on, the O position indicates power off). The switch automatically runs POST. WARNING: Do not connect the switch to the network until the IP address is correctly set. For instructions on setting the IP address, see "Configuring SAN Switch 2/32 Network Addressing" on page 39. 38 SAN Switch 2/32 Version 4.2.x Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
38
SAN Switch 2/32 Version 4.2.x Installation Guide
Connecting AC Power
Follow these steps to power on the SAN Switch 2/32.
Caution:
Do not plug the power cords into the power source until the switch is
completely installed in the rack.
1.
Connect the SAN Switch 2/32 power cords to the power connectors on the
switch as shown in
Figure 13
.
Figure 13:
Connecting the power cords
2.
Attach the remaining ends of the power cords to power outlets.
3.
Turn on the power switch (the
1
position indicates power on, the
O
position
indicates power off). The switch automatically runs POST.
WARNING:
Do not connect the switch to the network until the IP address is
correctly set. For instructions on setting the IP address, see “
Configuring SAN
Switch 2/32 Network Addressing
” on page 39.
SHR-2571A