HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 46

Connecting the SAN Switch 2/32 to the Fabric, HP StorageWorks Fabric OS 4.2.x Features, Guide

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing the SAN Switch 2/32 Note: Configure each port to match the topology of each host or target before connecting to the device. The default port configuration is fabric, not private loop. The switch does not auto-sense topology. Connecting the SAN Switch 2/32 to the Fabric Execute the following procedure to connect the SFPs and cables to SAN Switch 2/32 ports as required. Note: The ports and cables used in trunking groups must meet specific requirements. For a list of these requirements, refer to the HP StorageWorks Fabric OS 4.2.x Features Guide. 1. Remove the shipping plug from the appropriate ports. 2. Position the SFP so that the key (the tab near the cable-end of the SFP) is on top. 3. Insert the SFP into the port until it is firmly seated and the latching mechanism clicks. Note: The SFP is keyed so that it can be inserted only with the correct orientation into the port. If the SFP does not slide in easily, check the orientation. 46 SAN Switch 2/32 Version 4.2.x Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
46
SAN Switch 2/32 Version 4.2.x Installation Guide
Note:
Configure each port to match the topology of each host or target before
connecting to the device. The default port configuration is fabric, not private loop. The
switch does not auto-sense topology.
Connecting the SAN Switch 2/32 to the Fabric
Execute the following procedure to connect the SFPs and cables to SAN Switch
2/32 ports as required.
Note:
The ports and cables used in trunking groups must meet specific requirements.
For a list of these requirements, refer to the
HP StorageWorks Fabric OS 4.2.x Features
Guide
.
1.
Remove the shipping plug from the appropriate ports.
2.
Position the SFP so that the key (the tab near the cable-end of the SFP) is on
top.
3.
Insert the SFP into the port until it is firmly seated and the latching
mechanism clicks.
Note:
The SFP is keyed so that it can be inserted only with the correct orientation into
the port. If the SFP does not slide in easily, check the orientation.