HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 45

Optional Configuration Settings, Modifying Domain IDs, Specifying Custom Status Policies

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Installing the SAN Switch 2/32 If Extended Edge PID is set (before a downgrade from the current Fabric OS release to an earlier Fabric OS release that does not support the Extended PID format), PID needs to be set back to a supported format, such as Core PID (format 1) or native PID (format 0). Optional Configuration Settings This section describes how to modify domain IDs and status policies. Modifying Domain IDs Optional. Modify the domain IDs, if desired, as follows. Note: The default domain ID is 1. If the default domain ID is already in use when the switch is connected to the fabric, the domain ID for the new switch is automatically reset to a unique value. The domain IDs that are currently in use can be determined using the Telnet command fabricShow. 1. Disable the switch by issuing the switchDisable command. 2. Issue the configure command. 3. Enter y at the Fabric parameters prompt: Fabric parameters (y, n) 4. Enter a unique domain ID (such as the domain ID used by the previous switch, if still available): Domain: (1..239) [1] 3 5. Complete the remaining prompts (or press CTRL+D to accept the remaining settings without completing all the prompts). 6. Reenable the switch by issuing the switchEnable command. Specifying Custom Status Policies Optional. If desired, specify any custom status policies for the fabric as follows. 1. Issue the switchStatusPolicySet command. 2. Specify the desired status policies. To completely deactivate the alarm for a particular condition, enter 0 at the prompt for that condition. SAN Switch 2/32 Version 4.2.x Installation Guide 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
45
SAN Switch 2/32 Version 4.2.x Installation Guide
If Extended Edge PID is set (before a downgrade from the current Fabric OS
release to an earlier Fabric OS release that does not support the Extended PID
format), PID needs to be set back to a supported format, such as Core PID (format
1) or native PID (format 0).
Optional Configuration Settings
This section describes how to modify domain IDs and status policies.
Modifying Domain IDs
Optional. Modify the domain IDs, if desired, as follows.
Note:
The default domain ID is
1
. If the default domain ID is already in use when the
switch is connected to the fabric, the domain ID for the new switch is automatically reset
to a unique value. The domain IDs that are currently in use can be determined using the
Telnet command
fabricShow
.
1.
Disable the switch by issuing the
switchDisable
command.
2.
Issue the
configure
command.
3.
Enter
y
at the
Fabric parameters
prompt:
Fabric parameters (y, n)
4.
Enter a unique domain ID (such as the domain ID used by the previous
switch, if still available):
Domain: (1..239) [1] 3
5.
Complete the remaining prompts (or press
CTRL+D
to accept the remaining
settings without completing all the prompts).
6.
Reenable the switch by issuing the
switchEnable
command.
Specifying Custom Status Policies
Optional.
If desired, specify any custom status policies for the fabric as follows.
1.
Issue the
switchStatusPolicySet
command.
2.
Specify the desired status policies. To completely deactivate the alarm for a
particular condition, enter
0
at the prompt for that condition.