HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 42

Flow control: None, Enter the following information at the corresponding prompts, as shown

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Installing the SAN Switch 2/32 ■ Flow control: None To configure port settings in a UNIX® environment, enter: tip /dev/ttyb -9600 7. Log in to the switch as the admin user. The default admin logon is admin and the default password is password. a. Issue the ipAddrSet command at the prompt. b. Enter the following information at the corresponding prompts, as shown in the example below: Example switch:admin> ipaddrset Ethernet IP Address [10.77.77.77]:10.32.53.47 Ethernet Subnetmask [255.0.0.0]:255.255.240.0 Fibre Channel IP Address [0.0.0.0]: Fibre Channel Subnetmask [0.0.0.0]: Gateway IP Address [0.0.0.0]:10.32.48.1 Set IP address now? [y = set now, n = next reboot]:y IP address being changed... Committing configuration...Done. switch:admin> c. To verify that the IP address was entered correctly, issue the ipAddrShow command. d. After the IP address is verified as correct, remove the serial cable, and replace the shipping plug in the serial port. Caution: The serial port is intended for use only during the initial setting of the IP address and for service purposes. HP does not recommend using the serial port during normal switch operation or for regular maintenance. 8. Record the IP address on the label affixed to the SAN Switch 2/32. 42 SAN Switch 2/32 Version 4.2.x Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
42
SAN Switch 2/32 Version 4.2.x Installation Guide
■
Flow control: None
To configure port settings in a UNIX
®
environment, enter:
tip /dev/ttyb -9600
7.
Log in to the switch as the admin user. The default admin logon is
admin
and
the default password is
password
.
a.
Issue the
ipAddrSet
command at the prompt.
b.
Enter the following information at the corresponding prompts, as shown
in the example below:
Example
c.
To verify that the IP address was entered correctly, issue the
ipAddrShow
command.
d.
After the IP address is verified as correct, remove the serial cable, and
replace the shipping plug in the serial port.
Caution:
The serial port is intended for use only during the initial setting of the
IP address and for service purposes. HP does not recommend using the serial
port during normal switch operation or for regular maintenance.
8.
Record the IP address on the label affixed to the SAN Switch 2/32.
switch:admin> ipaddrset
Ethernet IP Address [10.77.77.77]:10.32.53.47
Ethernet Subnetmask [255.0.0.0]:255.255.240.0
Fibre Channel IP Address [0.0.0.0]:
Fibre Channel Subnetmask [0.0.0.0]:
Gateway IP Address [
0.0.0.0
]:10.32.48.1
Set IP address now? [y = set now, n = next
reboot]:y
IP address being changed...
Committing configuration...Done.
switch:admin>