HP StorageWorks 2/32 HP StorageWorks SAN Switch 2/32 V4.2.X Installation Guide - Page 40

Requirements, Setting Network Addresses via a Serial Connection, HP StorageWorks

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Installing the SAN Switch 2/32 For detailed information about the commands used in this procedure, refer to the HP StorageWorks Fabric OS 4.2.x Command Reference Guide. Requirements The following items are required for configuring and connecting the SAN Switch 2/32 in a network and fabric: ■ An unused IP address and corresponding subnetmask and gateway address from your Network Administrator ■ SAN Switch 2/32 installed and connected to a power source ■ A local workstation (desktop or notebook computer) with: - Microsoft® Windows 98, Windows 2000, Windows Millennium Edition, or Windows NT 4.0 operating system - RS-232 Serial communication software (for example, ProComm Plus or HyperTerminal) ■ Serial cable provided with the switch ■ Ethernet cable ■ SFP transceivers and compatible cables, as required ■ Access to an FTP server for backing up the switch configuration Setting Network Addresses via a Serial Connection Use the following steps to verify or change the SAN Switch 2/32 IP address, subnetmask, or gateway address. Note: During first time setup, you must replace the factory IP, subnetmask, and gateway addresses with addresses provided by your Network Administrator. 1. Remove the shipping plug from the SAN Switch 2/32 serial port. 2. Connect the Serial cable to the SAN Switch 2/32 serial port as shown in Figure 14. 40 SAN Switch 2/32 Version 4.2.x Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Installing the SAN Switch 2/32
40
SAN Switch 2/32 Version 4.2.x Installation Guide
For detailed information about the commands used in this procedure, refer to the
HP StorageWorks
Fabric OS
4.2.x Command Reference Guide.
Requirements
The following items are required for configuring and connecting the SAN Switch
2/32 in a network and fabric:
■
An unused IP address and corresponding subnetmask and gateway address
from your Network Administrator
■
SAN Switch 2/32 installed and connected to a power source
■
A local workstation (desktop or notebook computer) with:
— Microsoft
®
Windows 98, Windows 2000, Windows Millennium Edition,
or Windows NT 4.0 operating system
—
RS-232 Serial communication software (for example, ProComm Plus or
HyperTerminal)
■
Serial cable provided with the switch
■
Ethernet cable
■
SFP transceivers and compatible cables, as required
■
Access to an FTP server for backing up the switch configuration
Setting Network Addresses via a Serial Connection
Use the following steps to verify or change the SAN Switch 2/32 IP address,
subnetmask, or gateway address.
Note:
During first time setup, you must replace the factory IP, subnetmask, and
gateway addresses with addresses provided by your Network Administrator.
1.
Remove the shipping plug from the SAN Switch 2/32 serial port.
2.
Connect the Serial cable to the SAN Switch 2/32 serial port as shown in
Figure 14
.