Panasonic DMREZ485V Dvd Recorder - English/spanish - Page 83

Operation, Cannot operate the TV or Set Top

Page 83 highlights

General Issues Operation Cannot operate the TV or Set Top Box with the unit's remote control. Cannot operate the DVD. Cannot operate the VHS. The remote control doesn't work. The unit is on but cannot be operated. "U88" is displayed and the disc cannot be ejected. Cannot eject a disc. Startup is slow. A password screen appears and you are unable to view or record. Time is incorrect after using Auto Clock Setting.  Change the manufacturer code on the remote control.  Select TV or Set Top Box mode on the remote control.  Press [DRIVE SELECT] to select the DVD drive when operating DVDs or CDs. - Make sure the TV is on the correct channel or input mode.  Press [DRIVE SELECT] to select the VHS drive when operating VHS cassettes. - Make sure the TV is on the correct channel or input mode.  The remote control code is wrong. Change to the correct code.  The batteries are depleted. Replace them with new ones.  Point the remote control at the remote control sensor on the main unit.  Remove obstacles between the remote control and main unit.  Remove dust from the transmission window and the unit's sensor.  Colored glass may obstruct the signal reception/transmission.  Don't place the signal sensor in direct sunlight or in areas that may be subject to sun exposure.  It may be necessary to set the code on the remote control again after changing the batteries.  It may be necessary to set the manufacturer code again after changing the batteries.  Some operations are prohibited by the disc.  The unit is warm ("U59" appears on the unit's display). Wait until "U59" disappears.  One of the unit's safety devices may have been activated. Reset the unit as follows: Press [/I POWER] on the main unit to switch to off. If the unit doesn't switch to off, reset the unit ( 81, "To restore the unit if it freezes").  The unit is carrying out the recovery process. Do the following to eject the disc: (1)Press [/I POWER] on the main unit to switch to off. If the unit doesn't switch to off, reset the unit ( 81, "To restore the unit if it freezes"). (2)While the unit is off, press and hold [] and [CH ] on the main unit at the same time for about 5 seconds. (Ejection may take extra time depending on discs.) The disc may be defective. Try another disc.  The unit is recording.  The unit may have a problem. Eject the disc as in (2) above.  Startup takes time in the following situations: - A disc other than a DVD-RAM is inserted. - The clock is not set. - Immediately after a power failure or the AC power supply cord is connected. - When the unit is connected with an HDMI cable.  If the unit starts receiving a broadcast with the set rating information, a password screen appears and you will be unable to view or record. Enter your password to continue.  Try again. If the time is still incorrect, set the clock manually. Page 68 68 17 17 57 5 5 57 68 − − − − − − − 56 58 Reference 83 RQT9056

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100

83
RQT9056
Cannot operate the TV or Set Top
Box with the unit’s remote control.
Change the manufacturer code on the remote control.
68
Select TV or Set Top Box mode on the remote control.
68
Cannot operate the DVD.
Press [DRIVE SELECT] to select the DVD dri
v
e when operating DVDs or
CDs.
Make sure the TV is on the correct channel or input mode.
17
Cannot operate the VHS.
Press [DRIVE SELECT] to select the VHS dri
v
e when operating VHS
cassettes.
Make sure the TV is on the correct channel or input mode.
17
The remote control doesn’t work.
The remote control code is wrong. Change to the correct code.
57
The batteries are depleted. Replace them with new ones.
5
Point the remote control at the remote control sensor on the main unit.
5
Remo
v
e obstacles between the remote control and main unit.
±
Remo
v
e dust from the transmission window and the unit’s sensor.
±
Colored glass may obstruct the signal reception/transmission.
±
Don’t place the signal sensor in direct sunlight or in areas that may be
subject to sun exposure.
±
It may be necessary to set the code on the remote control again after
changing the batteries.
57
It may be necessary to set the manufacturer code again after changing the
batteries.
68
The unit is on but cannot be
operated.
Some operations are prohibited by the disc.
±
The unit is warm (“U59” appears on the unit’s display).
W
ait until “U59”
disappears.
±
One of the unit’s safety de
v
ices may ha
v
e been acti
v
ated.
Reset the unit as follows:
Press [
/I PO
W
ER] on the main unit to switch to off.
If the unit doesn’t switch to off, reset the unit (
¼
81, “To restore the unit if it
freezes”).
±
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the reco
v
ery process. Do the following to eject the
disc:
(1)Press [
/I PO
W
ER] on the main unit to switch to off.
If the unit doesn’t switch to off, reset the unit (
¼
81, “To restore the unit if
it freezes”).
(2)
W
hile the unit is off, press and hold [
] and [CH
] on the main unit
at the same time for about 5 seconds. (Ejection may take extra time
depending on discs.) The disc may be defecti
v
e. Try another disc.
±
Cannot eject a disc.
The unit is recording.
±
The unit may ha
v
e a problem. Eject the disc as in (2) abo
v
e.
±
Startup is slow.
Startup takes time in the following situations:
A disc other than a DVD-RAM is inserted.
The clock is not set.
Immediately after a power failure or the AC power supply cord is
connected.
W
hen the unit is connected with an HDMI cable.
±
A password screen appears and
you are unable to
v
iew or record.
If the unit starts recei
v
ing a broadcast with the set rating information, a
password screen appears and you will be unable to
v
iew or record. Enter
your password to continue.
56
Time is incorrect after using Auto
Clock Setting.
Try again. If the time is still incorrect, set the clock manually.
58
General Issues
Operation
Page
Reference