Yamaha Tyros4 Owner's Manual - Page 109

Removing Flash Memory Expansion, Module, tioning properly.

Get Yamaha Tyros4 PDF manuals and user guides
UPC - 086792947280
View all Yamaha Tyros4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

3 Remove the four screws from the cover. (Rear side) NOTE Keep the removed screws in a safe place. They will be used when reattaching the cover to the instrument after installation. 4 Insert the module into the socket by fol- lowing the procedure below. 4-1 Insert the module vertically in the socket and position the screws (of the module) to the female screws respectively. Connector Flash Memory Expansion Module Female screw Socket Female screw (Rear side) 4-2 Press the top of the connector as shown, then push the connector firmly into the socket. 4-3 5 Re-install the cover you removed in step 3, in reverse order. 6 Check that the installed module is func- tioning properly. 6-1 Set the Tyros4 right-side up, and then turn the power on. 6-2 Call up the Format operation display. [VOICE CREATOR]  [E] EXPANSION MODULE 6-3 Execute the Format operation following the messages on the display. If the module has been installed properly, the appropriate available memory size is indicated in the PROPERTY display. ([VOICE CREATOR]  [E] EXPANSION MODULE  [7 ]-[8 ] PROPERTY) Removing Flash Memory Expansion Module 1 Loosen both the screws with your hand as shown below. 1 2 4-2 4-3 Tighten each screw of the module to each female screw of the Tyros4 with your hand as shown. NOTICE • If you cannot loosen the screws with your hand, use a Phillips screwdriver. In this case, be careful NOT to scratch the module or the Tyros4. • Be careful NOT to drop the screws inside the instrument when loosening them. 2 Pull the module vertically out of the socket. 3 Attach the cover to the bottom panel. Installing the Optional Flash Memory Expansion Module Tyros4 Owner's Manual 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Tyros4
Owner’s Manual
109
Installing the Optional Flash Memory Expansion Module
3
Remove the four screws from the cover.
4
Insert the module into the socket by fol-
lowing the procedure below.
4-1
Insert the module vertically in the socket and
position the screws (of the module) to the
female screws respectively.
4-2
Press the top of the connector as shown, then
push the connector firmly into the socket.
4-3
Tighten each screw of the module to each
female screw of the Tyros4 with your hand as
shown.
5
Re-install the cover you removed in step
3, in reverse order.
6
Check that the installed module is func-
tioning properly.
6-1
Set the Tyros4 right-side up, and then turn the
power on.
6-2
Call up the Format operation display.
[VOICE CREATOR]
[E] EXPANSION
MODULE
6-3
Execute the Format operation following the
messages on the display.
If the module has been installed properly, the appro-
priate available memory size is indicated in the
PROPERTY display.
([VOICE CREATOR]
[E] EXPANSION MOD-
ULE
[7
]–[8
] PROPERTY)
Removing Flash Memory Expansion
Module
1
Loosen both the screws with your hand
as shown below.
2
Pull the module vertically out of the
socket.
3
Attach the cover to the bottom panel.
Keep the removed screws in a safe place. They will be used when reattaching the
cover to the instrument after installation.
(Rear side)
NOTE
Flash Memory
Expansion Module
Connector
Female screw
Socket
Female screw
(Rear side)
4-3
4-2
• If you cannot loosen the screws with your hand, use a Phillips
screwdriver. In this case, be careful NOT to scratch the module or
the Tyros4.
• Be careful NOT to drop the screws inside the instrument when loos-
ening them.
1
2
NOTICE