Casio EX-Z70 Owners Manual - Page 230

and then try again., After confirming that the computer is

Page 230 highlights

APPENDIX Symptom All buttons and switches are disabled. Monitor screen is off. Possible Cause Circuit problem caused by electrostatic charge, impact, etc. while the camera was connected to another device. USB communication is in progress. Cannot transfer files over a 1) USB cable is not connected securely. USB connection. 2) USB driver is not installed. 3) Camera is turned off. Display language setting screen appears when the camera is turned on. 1) Camera's display language, Home city, date style, date and time, and other settings have not been configured. 2) A problem with the camera's built-in memory management area. Action Remove the battery from the camera, reinsert it, and then try again. After confirming that the computer is not accessing camera memory, disconnect the USB cable. 1) Check all connections. 2) Install the USB driver on your computer (page 189). 3) Turn on the camera. 1) Check the settings (page 46). 2) Perform the reset operation to initialize the camera's setup (page 123). After that, configure each setting. If the language selection screen does not re-appear when you turn the camera on, it means that the camera's built-in memory management area has been restored. If the same message appears after you turn power back on, contact your retailer or a CASIO service center. Other 230

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239

APPENDIX
230
Symptom
Possible Cause
Action
Other
All buttons and switches
are disabled.
Monitor screen is off.
Cannot transfer files over a
USB connection.
Display language setting
screen appears when the
camera is turned on.
Circuit problem caused by electrostatic charge,
impact, etc. while the camera was connected to
another device.
USB communication is in progress.
1)
USB cable is not connected securely.
2)
USB driver is not installed.
3)
Camera is turned off.
1) Camera
s display language, Home city, date
style, date and time, and other settings have
not been configured.
2)
A problem with the camera
s built-in memory
management area.
Remove the battery from the camera, reinsert it,
and then try again.
After confirming that the computer is not
accessing camera memory, disconnect the USB
cable.
1)
Check all connections.
2)
Install the USB driver on your computer (page
189).
3)
Turn on the camera.
1)
Check the settings (page 46).
2)
Perform the reset operation to initialize the
camera
s setup (page 123). After that, configure
each setting. If the language selection screen
does not re-appear when you turn the camera
on, it means that the camera
s built-in memory
management area has been restored. If the
same message appears after you turn power
back on, contact your retailer or a CASIO
service center.