Casio EX-Z70 Owners Manual - Page 67

Flash Precautions, to select the setting you, want, and then press [SET].

Page 67 highlights

BASIC IMAGE RECORDING 4. Use [̆] and [̄] to select the setting you want, and then press [SET]. To do this: Turn on flash assist Turn off flash assist Select this setting: Auto Off IMPORTANT! • Flash assist may not produce the desired result for some types of subjects. • Flash assist may have little effect on your image if you changed any of the following settings when you recorded it. - Flash intensity (page 66) - Exposure compensation (EV shift) (page 82) - ISO sensitivity (page 117) - Contrast (page 121) • Using flash assist can cause an increase of digital noise in recorded images. I Flash Precautions • Take care that your fingers do not block the flash when you hold the camera. Covering the flash with your finger can greatly reduce its effectiveness. Flash • You may not be able to achieve the desired results using the flash if the subject is too close or too far away. • The flash takes anywhere from a few seconds to as long as 7 seconds to attain full charge after being fired. The actual time required depends on the battery level, temperature, and other conditions. • The flash unit may not be able to charge when camera battery power is low. If this happens, the flash will not fire properly and you will not be able to obtain the desired exposure. Be sure to charge the camera's battery as soon as possible when power goes low. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239

BASIC IMAGE RECORDING
67
Flash Precautions
Take care that your fingers
do not block the flash when
you hold the camera.
Covering the flash with your
finger can greatly reduce its
effectiveness.
You may not be able to achieve the desired results using
the flash if the subject is too close or too far away.
The flash takes anywhere from a few seconds to as long
as 7 seconds to attain full charge after being fired. The
actual time required depends on the battery level,
temperature, and other conditions.
The flash unit may not be able to charge when camera
battery power is low. If this happens, the flash will not fire
properly and you will not be able to obtain the desired
exposure. Be sure to charge the camera
s battery as soon
as possible when power goes low.
Flash
4.
Use [
³
] and [
´
] to select the setting you
want, and then press [SET].
IMPORTANT!
Flash assist may not produce the desired result for
some types of subjects.
Flash assist may have little effect on your image if
you changed any of the following settings when you
recorded it.
Flash intensity (page 66)
Exposure compensation (EV shift) (page 82)
ISO sensitivity (page 117)
Contrast (page 121)
Using flash assist can cause an increase of digital
noise in recorded images.
Select this setting:
Auto
Off
To do this:
Turn on flash assist
Turn off flash assist