Home » Cisco Manuals » Networking » Cisco 5505 » Manual Viewer

Cisco 5505 Administration Guide - Page 51

Using Compression, compression svc - cli

UPC - 882658082252

Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 5 Configuring AnyConnect Features Using ASDM Configuring, Enabling, and Using Other AnyConnect Features Figure 5-8 SSL Settings Dialog Box In the Certificates area, specify which certificates, if any, you want to use for SSL authentication on each interface. If you do not specify a certificate for a particular interface, the fallback certificate will be used. In the Fallback Certificate field, select a certificate from the drop-down list. The default is --None--. Using Compression On low-bandwidth connections, compression increases the communications performance between the security appliance and the client by reducing the size of the packets being transferred. By default, compression for all SSL VPN connections is enabled on the security appliance, both at the global level and for specific groups or users. For broadband connections, compression might result in poorer performance. By default, if you have not changed the compression setting globally, compression is enabled. You can configure compression globally using the CLI command compression svc command from global configuration mode. OL-12950-012 Cisco AnyConnect VPN Client Administrator Guide 5-9

Section	Page
About This Guide 7	3
chapter 1	3
Introduction 1	3
chapter 2	3
Common AnyConnect VPN Client Installation and Configuration Procedures 1	3
chapter 3	4
Installing the AnyConnect Client and Configuring the Security Appliance with ASDM 1	4
chapter 4	4
Installing the AnyConnect Client on a Security Appliance Using CLI 1	4
chapter 5	4
Configuring AnyConnect Features Using ASDM 1	4
chapter 6	4
Configuring AnyConnect Features Using CLI 1	4
chapter 7	5
Configuring and Using AnyConnect Client Operating Modes and User Profiles 1	5
chapter 8	5
Customizing and Localizing the AnyConnect Client 1	5
chapter 9	5
Monitoring and Maintaining the AnyConnect Client 1	5
appendix A	5
Sample AnyConnect Profile and XML Schema 1	5
appendix B	6
Using Microsoft Active Directory to Add the Security Appliance to the List of Internet Explorer Trusted Sites for Domain Users 1	6
Index	6
About This Guide	7
Document Objectives	7
Audience	7
Related Documentation	8
Document Organization	8
Document Conventions	9
Obtaining Documentation, Obtaining Support, and Security Guidelines	10
Licensing	10
Introduction	11
AnyConnect Client Features	11
Remote User Interface	12
Getting and Installing the Files You Need	17
CSA Interoperability with the AnyConnect Client and Cisco Secure Desktop	17
Common AnyConnect VPN Client Installation and Configuration Procedures	19
Installing the AnyConnect Client	19
Before You Install the AnyConnect Client	20
Ensuring Automatic Installation of AnyConnect Clients	20
AnyConnect Client and New Windows Installations	21
Adding a Security Appliance to the List of Trusted Sites (Internet Explorer)	21
Adding a Security Certificate in Response to Browser Security Alert Windows	22
Replacing a Digital Certificate with a Trusted Certificate	25
Installing the AnyConnect Client on a User’s PC	26
Where to Find the AnyConnect Client Files to Install	26
Installing the AnyConnect Client Using the Microsoft Windows Installer on a PC Running Windows	26
Installing the AnyConnect Client on a PC Running Linux	27
Installing the AnyConnect Client on a PC Running MAC OSX	27
Installing the AnyConnect Client and Configuring the Security Appliance with ASDM	29
Installing the AnyConnect Client on a Security Appliance Using CLI	39
Enabling AnyConnect Client SSL VPN Connections Using CLI	40
Disabling Permanent Client Installation	42
Configuring AnyConnect Features Using ASDM	43
Enabling Datagram Transport Layer Security (DTLS) with AnyConnect (SSL) Connections	43
Configuring DTLS	44
Prompting Remote Users	46
Enabling IPv6 VPN Access	47
Enabling Modules for Additional AnyConnect Features	47
Configuring, Enabling, and Using Other AnyConnect Features	48
Configuring Certificate-only Authentication	48
Using Compression	51
Changing Compression Globally	52
Changing Compression for Groups and Users	52
Enabling AnyConnect Keepalives	53
Enabling AnyConnect Rekey	54
Enabling and Adjusting Dead Peer Detection	56
Configuring the Dynamic Access Policies Feature of the Security Appliance	57
Cisco Secure Desktop Support	57
Configuring AnyConnect Features Using CLI	59
Enabling Datagram Transport Layer Security (DTLS) with AnyConnect (SSL) Connections	59
Enabling DTLS Globally for a Specific Port	60
Enabling DTLS for Specific Groups or Users	60
Prompting Remote Users	60
Enabling IPv6 VPN Access	61
Enabling Modules for Additional AnyConnect Features	62
Configuring, Enabling, and Using Other AnyConnect Features	63
Configuring Certificate-only Authentication	63
Using Compression	63
Configuring the Dynamic Access Policies Feature of the Security Appliance	64
Cisco Secure Desktop Support	64
Enabling AnyConnect Rekey	64
Enabling and Adjusting Dead Peer Detection	65
Enabling AnyConnect Keepalives	66
Configuring and Using AnyConnect Client Operating Modes and User Profiles	67
AnyConnect Client Operating Modes	67
Using the AnyConnect CLI Commands to Connect (Standalone Mode)	67
Connecting Using WebLaunch	69
User Log In and Log Out	70
Logging In	70
Logging Out	70
Configuring and Using User Profiles	70
Enabling AnyConnect Client Profile Downloads	71
Configuring Profile Attributes	76
Enabling Start Before Logon (SBL) for the AnyConnect Client	77
XML Settings for Enabling SBL	77
CLI Settings for Enabling SBL	77
Configuring the ServerList Attribute	78
Configuring the Certificate Match Attribute	78
Certificate Key Usage Matching	78
Extended Certificate Key Usage Matching	79
Certificate Distinguished Name Mapping	79
Certificate Matching Example	81
Customizing and Localizing the AnyConnect Client	83
Customizing the End-user Experience	83
Language Translation (Localization) for User Messages	85
Understanding Language Translation	85
Configuring Language Localization Using ASDM	86
Creating or Modifying a Translation Table Using ASDM	88
Import/Export Language Localization	89
Creating or Modifying a Translation Table Using CLI	90
Monitoring and Maintaining the AnyConnect Client	95
Viewing AnyConnect Client and SSL VPN Sessions	95
Adjusting MTU Size Using ASDM	96
Adjusting MTU Size Using CLI	96
Logging Off AnyConnect Client Sessions	97
Updating AnyConnect Client and SSL VPN Client Images	98
Sample AnyConnect Profile and XML Schema	99
Sample AnyConnect Profile	99
Sample AnyConnect Profile Schema	101
Using Microsoft Active Directory to Add the Security Appliance to the List of Internet Explorer Trusted Sites for Domain Users	113
Index	115
A	115
C	115
D	115
E	115
F	115
G	116
I	116
K	116
L	116
M	116
N	116
O	116
P	117
R	117
S	117
T	117
U	117
V	118
W	118

Match case Limit results 1 per page

5-9

Cisco AnyConnect VPN Client Administrator Guide

OL-12950-012

Chapter 5

Configuring AnyConnect Features Using ASDM

Configuring, Enabling, and Using Other AnyConnect Features

Figure 5-8

SSL Settings Dialog Box

In the Certificates area, specify which certificates, if any, you want to use for SSL authentication on each

interface. If you do not specify a certificate for a particular interface, the fallback certificate will be used.

In the Fallback Certificate field, select a certificate from the drop-down list. The default is --None--.

Using Compression

On low-bandwidth connections, compression increases the communications performance between the

security appliance and the client by reducing the size of the packets being transferred. By default,

compression for all SSL VPN connections is enabled on the security appliance, both at the global level

and for specific groups or users. For broadband connections, compression might result in poorer

performance.

By default, if you have not changed the compression setting globally, compression is enabled. You can

configure compression globally using the CLI command

compression svc

command from global

configuration mode.