Compaq ProLiant 8000 ProLiant 8000 Servers Maintenance and Service Guide - Page 152

If the ProLiant Storage System, Check SCSI cables. If

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

Diagnostics and Troubleshooting 6-25 Table 6-2 POST Error Messages continued Error Code Audible Beeps 1777-Slot X Drive None Array - ProLiant Drive Storage Enclosure Problem Detected (followed by one or more of the following): SCSI Port Y: Cooling Fan Malfunction Detected SCSI Port Y: Overheated Condition Detected SCSI Port Y: Side-Panel must be Closed to Prevent Overheating SCSI Port Y: Redundant Power Supply Malfunction Detected SCSI Port Y: Wide SCSI Transfer Failed SCSI Port Y: Interrupt Signal Inoperative (RESUME = F1 KEY) 1778-Drive Array None resuming Automatic Data Recovery process 1779-Slot X Drive None Array - Replacement drive(s) detected OR previously failed drive(s) now operational: Port Y: SCSI ID Z: Restore data from backup if replacement drive X has been installed. 1780-Disk 0 Failure None 1781-Disk 1 Failure None Probable Source of Problem Temperature violation detected. Recommended Action Check cooling fan operation by placing hand over fan. Verify internal plenum cooling fan in tower servers or storage systems is operational. If fan is not operating, check for obstructions and verify all internal connections. Replace unit side panel if removed. If the ProLiant Storage System power LED is amber instead of green, this indicates a redundant power supply failure. Check SCSI cables. If the message indicates to check SCSI cables, verify your cabling against the diagrams in your Compaq Smart Array Controller user guide. If the routing is correct, replace cables on the specified port until the POST message is eliminated. This message appears whenever a controller reset or power cycle occurs while Automatic Data Recovery is in progress. Intermittent drive failure and/or possible loss of data detected. No action necessary. If this message displays and drive X has not been replaced, this indicates an intermittent drive failure. This message also displays immediately following drive replacement whenever data must be restored from backup. Hard drive/format error detected. Hard drive/format error detected. Run Compaq Diagnostics. Replace failed assembly as indicated. Run Compaq Diagnostics. Replace failed assembly as indicated. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
Diagnostics and Troubleshooting
6-25
Table 6-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1777-Slot
X
Drive
Array
–
ProLiant
Drive Storage
Enclosure Problem
Detected (followed by
one or more of the
following):
SCSI Port
Y
: Cooling
Fan Malfunction
Detected
SCSI Port
Y
:
Overheated Condition
Detected
SCSI Port
Y
:
Side-Panel must be
Closed to Prevent
Overheating
SCSI Port
Y
:
Redundant Power
Supply Malfunction
Detected
SCSI Port
Y
: Wide
SCSI Transfer Failed
SCSI Port
Y
: Interrupt
Signal Inoperative
(RESUME = F1 KEY)
None
Temperature violation detected.
Check cooling fan operation by
placing hand over fan. Verify
internal plenum cooling fan in
tower servers or storage
systems is operational. If fan is
not operating, check for
obstructions and verify all
internal connections. Replace
unit side panel if removed.
If the ProLiant Storage System
power LED is amber instead of
green, this indicates a
redundant power supply failure.
Check SCSI cables. If the
message indicates to check
SCSI cables, verify your cabling
against the diagrams in your
Compaq Smart Array Controller
user guide. If the routing is
correct, replace cables on the
specified port until the POST
message is eliminated.
1778-Drive Array
resuming Automatic
Data Recovery
process
None
This message appears whenever
a controller reset or power cycle
occurs while Automatic Data
Recovery is in progress.
No action necessary.
1779-Slot
X
Drive
Array
–
Replacement
drive(s) detected OR
previously failed
drive(s) now
operational:
Port
Y
: SCSI ID
Z
:
Restore data from
backup if
replacement drive
X
has been installed.
None
Intermittent drive failure and/or
possible loss of data detected.
If this message displays and
drive
X
has not been replaced,
this indicates an intermittent
drive failure. This message also
displays immediately following
drive replacement whenever
data must be restored from
backup.
1780-Disk 0 Failure
None
Hard drive/format error detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
1781-Disk 1 Failure
None
Hard drive/format error detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
continued