Home » Dell Manuals » Servers » Dell EqualLogic PS6210XS » Manual Viewer

Dell EqualLogic PS6210XS EqualLogic Host Integration Tools for Microsoft Editi - Page 31

List or Modify MPIO Settings

View all Dell EqualLogic PS6210XS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Parameter Argument SerialNumber= serial number ServiceTag= service tag number MemberName= member name MemberIPEth0= IP address MemberSubnet= subnet mask MemberGateway= IP address CreateGroup GroupName= group name JoinGroup GroupIP= Admin= IP address group admin password Membership= RAID= ChapUser= password 10|50|6|6‑accelerated CHAP user name ChapSecret= DCBVlanID= CHAP password data center bridging VLAN ID Description you must also enter the ‑GroupName and ‑GroupIP command parameters. Designates the serial number of the PS Series array to be initialized. Use either this option or the ServiceTag option, but not both. Designates the service tag number of the PS Series array to be initialized. Use either this option or the SerialNumber option, but not both. (Required) Designates the member name of the PS Series array to be initialized. (Required) Designates the IP address for the Ethernet 0 network interface that controls access to the PS Series array to be initialized. (Required) Designates the IP address for the subnet controlling access to the PS Series array to be initialized. (Required) Designates the IP address of the gateway to use for access to the PS Series array to be initialized. Specifies that a new group should be created using the specified group name and group IP address. Make sure the name and IP address you enter are not used by any other group. (Required with CreateGroup) Designates the name of a specific PS Series group for which configuration information is requested. Specifies that the member array should join the group with the specified group name and group IP address. Designates the IP address to be used for accessing the group. (Required with CreateGroup) Specifies the password to be used for default group administration user access to the specified group. Specifies the password to be used for authenticating membership access to the specified group. (Required with CreateGroup) Specifies the RAID policy for the member. (Required with CreateGroup) Specifies the CHAP user name to be used for authenticating access to arrays in the specified group. (Required with CreateGroup) Specifies the password to be used for authenticating access to arrays in the specified group. Designates the VLAN ID if you are using data center bridging (DCB). NOTE: For a complete listing of RAID policies on PS Series systems, see the Dell Technical Report PS Series Storage Arrays: Choosing a Member RAID Policy, available from the following location: en.community.dell.com/techcenter/storage/w/wiki/equallogic-tech-reports.aspx List or Modify MPIO Settings Use the rswcli ‑MPIOParameters command to list or modify MPIO settings. Remote Setup Command Line Utility 31

Section	Page
Dell EqualLogic Host Integration Tools for Microsoft Edition Version 5.3 Installation and User's Guide	3
About This Guide	6
Revision History	6
Audience	6
Support Resources	6
Download the Installation Kit	6
Related Documentation	6
Dell Online Services	6
Contacting Dell	7
Introduction to Host Integration Tools	8
Host Integration Tools Components	8
SMP Support	9
SMP Configuration	9
SCVMM Support	9
Configure SCVMM	9
Supported SCVMM Operations	10
Supported Applications	10
Microsoft Exchange Server	10
Microsoft SQL Server	10
Microsoft Hyper-V	11
SharePoint	11
Installation	12
Obtain the Installation Kit	12
Download the Installation Kit	12
Administrative Installation Using Active Directory	12
Installation Considerations	13
Install Host Integration Tools for Microsoft	13
Update an Installation	14
Uninstall HIT or a Component	14
Install HIT/Microsoft on a Windows Server 2012 R2 Core Machine	14
Install HIT on a Windows Server 2012 R2 Core Cluster	15
About Remote Host Installations	15
Install HIT on Remote Hosts With the Add Hosts Wizard	15
Procedure for Installing HIT on Remote Hosts with the Add Hosts Wizard	16
Install HIT on Remote Hosts Using PowerShell Scripts	16
Syntax for PowerShell Remote Host Installation	17
Procedure for Installing HIT on Remote Hosts With PowerShell	18
Install HIT on a Failover Cluster	18
Specify the ASM/ME Backup Document Directory	19
Change the Login Account for ASM/ME Services (EQLReqService and EqlASMAgent)	19
Join a Computer into a Failover Cluster	19
About Silent Installations	19
Support for a Silent Installation	20
Syntax	20
Perform a Silent Installation	20
Perform a Silent Uninstallation	21
Create a Log File During Silent Mode	21
Using HIT With a SharePoint Farm	21
Specify Index File Locations When Installing SharePoint	21
Modify Index File Locations in an Existing SharePoint Farm	22
Change the Default Index File Location Using PowerShell cmdlets	23
Change Index File Locations Using Central Administration	23
Change Administration Component Index File Location	23
Change the SPSearch Index File Location	23
Best Practices for SharePoint	24
Remote Setup Wizard	25
PS Series Group Requirements for Using RSW	25
Windows System Requirements for Using RSW	25
Launch RSW on the Host	25
Launch RSW From ASM/ME	26
Initialize a PS Series Array Using RSW	26
Search for a PS Series Array Using RSW	26
Information Required for Initializing a PS Series Array	26
Initialize an Array and Create a PS Series Group	27
Initialize an Array and Add It to an Existing Group	28
Troubleshoot RSW	28
Remote Setup Command Line Utility	29
General Command Syntax for the RSWCLI	29
Getting Help on Commands	29
Using RSWCLI Commands	30
Discover a PS Series Array	30
Initialize a PS Series Array	30
List or Modify MPIO Settings	31
List Included and Excluded Subnets for MPIO	32
Include a Subnet or Adapter for Use by MPIO	33
Exclude a Subnet or Adapter From Use By MPIO	33
Using the Multipath I/O Component	35
Introduction to Multipath I/O DSM	35
Determining the Number of iSCSI Sessions for a Volume Slice	36
Prerequisites for Configuring Multipath I/O DSM	37
Requirements for Multipath I/O	37
Configure Multipath I/O Between a Computer and a Group	38
Log In to a Volume With Multipath I/O	38
Log Off a Volume With Multipath I/O on Variants of Windows Operating Systems	39
View MPIO Sessions	39
Set the MPIO Load-Balancing Policy	41
On Other Operating Systems	41
EqualLogic MPIO Configuration Tool	41
Use the VDS Provider	43
VDS Provider Requirements	43
VDS Provider Guidelines and Restrictions	43
Simple Target and LUN Naming	43
Import VSS Snapshots	44
Adjustments After Access Control Modifications	44
Create a Volume Using Storage Manager for SANs	44
Start Storage Manager for SANs	44
Use SCVMM With the Dell EqualLogic SMP	46
Install the Dell EqualLogic Storage Management Provider	46
Configure the Dell EqualLogic Storage Management Provider	46
Create a Classification for Dell EqualLogic Storage Resources	47
Import the SMP Through the SCVMM GUI	47
Configure PS Series Groups	49
Configure Group Access on Managed Hosts and Clusters	50
Configure Storage for VM Rapid Provisioning	51
Create a VM Template for the Library Share	52
Create a VM Template From a VHD	53
Migrate the Rapid-Provisioned VMs	55
Migrate Storage of a Deployed VM to Another Location	56
Troubleshoot SCVMM Issues	57
Supported SMP PowerShell Cmdlets	57
Use the HPC iSCSI Provider	59
About the HPC iSCSI Provider Installation	59
Configure the PS Series Array	59
HPC iSCSI Provider Settings	59
Tools and Utilities	61
EqlXcp Utility	61
EqlXcp Utility Restrictions	61
Run the EqlXcp Utility	61
EqlLog Utility	62
EqlLog Utility Overview	62
Run the EqlLog Utility	62
EqlLog Command Line Options	62
Trace Log Daemon	63
EqlRethin Utility	63
Run the EqlRethin Utility	63
Index	65
Special Characters	65
A	65
B	65
C	65
D	65
E	65
F	65
G	65
H	66
I	66
K	66
L	66
M	66
N	67
P	67
R	67
S	68
T	68
U	68
V	69
W	69

Match case Limit results 1 per page

Parameter

Argument

Description

you must also enter the

‑

GroupName

and

‑

GroupIP

command parameters.

SerialNumber=

serial number

Designates the serial number of the PS Series array to be

initialized. Use either this option or the

ServiceTag

option,

but not both.

ServiceTag=

service tag number

Designates the service tag number of the PS Series array to be

initialized. Use either this option or the

SerialNumber

option,

but not both.

MemberName=

member name

(Required) Designates the member name of the PS Series

array to be initialized.

MemberIPEth0=

IP address

(Required) Designates the IP address for the Ethernet 0

network interface that controls access to the PS Series array

to be initialized.

MemberSubnet=

subnet mask

(Required) Designates the IP address for the subnet controlling

access to the PS Series array to be initialized.

MemberGateway=

IP address

(Required) Designates the IP address of the gateway to use for

access to the PS Series array to be initialized.

CreateGroup

Specifies that a new group should be created using the

specified group name and group IP address. Make sure the

name and IP address you enter are not used by any other

group.

GroupName=

group name

(Required with CreateGroup) Designates the name of a

specific PS Series group for which configuration information is

requested.

JoinGroup

Specifies that the member array should join the group with the

specified group name and group IP address.

GroupIP=

IP address

Designates the IP address to be used for accessing the group.

Admin=

group admin password

(Required with CreateGroup) Specifies the password to be

used for default group administration user access to the

specified group.

Membership=

password

Specifies the password to be used for authenticating

membership access to the specified group.

RAID=

10|50|6|6

‑

accelerated

(Required with CreateGroup) Specifies the RAID policy for the

member.

ChapUser=

CHAP user name

(Required with CreateGroup) Specifies the CHAP user name to

be used for authenticating access to arrays in the specified

group.

ChapSecret=

CHAP password

(Required with CreateGroup) Specifies the password to be

used for authenticating access to arrays in the specified group.

DCBVlanID=

data center bridging VLAN ID

Designates the VLAN ID if you are using data center bridging

(DCB).

NOTE:

For a complete listing of RAID policies on PS Series systems, see the

Dell Technical Report PS Series Storage

Arrays: Choosing a Member RAID Policy

, available from the following location:

en.community.dell.com/techcenter/storage/w/wiki/equallogic-tech-reports.aspx

List or Modify MPIO Settings

Use the

rswcli

‑

MPIOParameters

command to list or modify MPIO settings.

Remote Setup Command Line Utility