Dell PowerEdge C6105 Hardware Owner's Manual - Page 27

DQS Rcvr En pass window CHA to CH B too large Pause, No DQS Receiver Enable pass window found

Get Dell PowerEdge C6105 PDF manuals and user guides View all Dell PowerEdge C6105 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Error Code Error Message Response 4108 Dram ECC requested but not enabled Pause 4109 Online spare requested but not enabled Pause 410A DIMM(s) Running in Minimum Mode Pause 410B No DQS Receiver Enable pass window found Pause 410C DQS Rcvr En pass window CHA to CH B too large Pause 410D DQS Rcvr En pass window too small (far right of Pause dynamic range) 4160 The processor(s) installed in your system are not halt multiprocessing capable. 5120 CMOS cleared by jumper Pause 5121 Password cleared by jumper Pause 8101 Warning! USB Host Controller not found at the Warning specified address!!! 8102 Error! USB device failed to initialize!!! Warning 8103 Warning! Unsupported UBS device found and disabled!!! Warning 8104 Warning! Port 60h/64h emulation is not supported Warning by this USB Host Controller!!! 8105 Warning! EHCI controller disabled. It requires 64bit data support in the BIOS. Pause 8400 Warning!! Insufficient memory! Remote access is Warning disabled. 8601 Error: BMC Not Responding Pause 8701 Insufficient Runtime space for MPS data!! Pause System may operate in PIC or Non-MPS mode. About Your System | 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
About Your System |
27
Error Code Error Message
Response
4108
Dram ECC requested but not enabled
Pause
4109
Online spare requested but not enabled
Pause
410A
DIMM(s) Running in Minimum Mode
Pause
410B
No DQS Receiver Enable pass window found
Pause
410C
DQS Rcvr En pass window CHA to CH B too large Pause
410D
DQS Rcvr En pass window too small (far right of
dynamic range)
Pause
4160
The processor(s) installed in your system are not
multiprocessing capable.
halt
5120
CMOS cleared by jumper
Pause
5121
Password cleared by jumper
Pause
8101
Warning! USB Host Controller not found at the
specified address!!!
Warning
8102
Error! USB device failed to initialize!!!
Warning
8103
Warning! Unsupported UBS device found and
disabled!!!
Warning
8104
Warning! Port 60h/64h emulation is not supported
by this USB Host Controller!!!
Warning
8105
Warning! EHCI controller disabled. It requires
64bit data support in the BIOS.
Pause
8400
Warning!! Insufficient memory! Remote access is
disabled.
Warning
8601
Error: BMC Not Responding
Pause
8701
Insufficient Runtime space for MPS data!!
System may operate in PIC or Non-MPS mode.
Pause