Dell PowerEdge R540 EMC Installation and Service Manual - Page 103

Processors and heat sinks, Removing a processor and heat sink module

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Figure 57. Installing a memory module Next steps 1. Installing the air shroud on page 77 2. Follow the procedure listed in After working inside your system on page 67. 3. To verify if the memory module has been installed properly, press F2 and navigate to System Setup Main Menu > System BIOS > Memory Settings. In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed memory. 4. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly seated in the memory module socket. 5. Run the system memory test in system diagnostics. Processors and heat sinks Removing a processor and heat sink module Prerequisites WARNING: The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to cool before removing it. 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Follow the procedure listed in Before working inside your system on page 67. 3. Remove the air shroud. Steps 1. Using a Torx #T30 screwdriver, loosen the screws on the heat sink in the order below: a. Loosen the first screw three turns. b. Loosen the second screw completely. c. Return to the first screw and loosen it completely. 2. Pushing both blue retention clips simultaneously, lift the processor and heat sink module (PHM) processor and heat sink module 3. Set the PHM aside with the processor side facing up. Installing and removing system components 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 57. Installing a memory module
Next steps
1.
Installing the air shroud
on page 77
2.
Follow the procedure listed in
After working inside your system
on page 67.
3.
To verify if the memory module has been installed properly, press F2 and navigate to
System Setup Main Menu > System BIOS >
Memory Settings
. In the
Memory Settings
screen, the System Memory Size must reflect the updated capacity of the installed
memory.
4.
If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly
seated in the memory module socket.
5.
Run the system memory test in system diagnostics.
Processors and heat sinks
Removing a processor and heat sink module
Prerequisites
WARNING:
The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to
cool before removing it.
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Follow the procedure listed in
Before working inside your system
on page 67.
3.
Remove the air shroud.
Steps
1.
Using a Torx #T30 screwdriver, loosen the screws on the heat sink in the order below:
a.
Loosen the first screw three turns.
b.
Loosen the second screw completely.
c.
Return to the first screw and loosen it completely.
2.
Pushing both blue retention clips simultaneously, lift the processor and heat sink module (PHM) processor and heat sink module
3.
Set the PHM aside with the processor side facing up.
Installing and removing system components
103