Dell PowerEdge R540 EMC Installation and Service Manual - Page 159

Installing the left control panel

Page 159 highlights

Steps 1. Disconnect the control panel cable from the system board connector. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. You must route the cables properly when you replace them to prevent the cables from being pinched or crimped. 2. Using a Phillips #1 screwdriver, remove the screws that secure the left control panel assembly to the system. Figure 122. Removing left control panel 3. Holding by the sides, remove the left control panel assembly away from the system. Next steps Installing the left control panel on page 159 Installing the left control panel Prerequisites Follow the safety guidelines listed in Safety instructions on page 66. Steps 1. Route the control panel cable through the side wall of the system. 2. Align the left control panel assembly with the control panel slot on the system and place the assembly in the slot on the system. 3. Connect the control panel cable to the system board connector. 4. Using Phillips #1 screwdriver, tighten the screws to secure the left control panel assembly to the system. Installing and removing system components 159

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175

Steps
1.
Disconnect the control panel cable from the system board connector.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. You must route
the cables properly when you replace them to prevent the cables from being pinched or crimped.
2.
Using a Phillips #1 screwdriver, remove the screws that secure the left control panel assembly to the system.
Figure 122. Removing left control panel
3.
Holding by the sides, remove the left control panel assembly away from the system.
Next steps
Installing the left control panel
on page 159
Installing the left control panel
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 66.
Steps
1.
Route the control panel cable through the side wall of the system.
2.
Align the left control panel assembly with the control panel slot on the system and place the assembly in the slot on the system.
3.
Connect the control panel cable to the system board connector.
4.
Using Phillips #1 screwdriver, tighten the screws to secure the left control panel assembly to the system.
Installing and removing system components
159