Dell PowerEdge R540 EMC Installation and Service Manual - Page 85

Removing the PERC card from the internal PERC riser

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Figure 40. Installing internal PERC riser 5. Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch. Next steps 1. Installing the air shroud on page 77 2. Follow the procedure listed in After working inside your system on page 67. Removing the PERC card from the internal PERC riser Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Follow the procedure listed in Before working inside your system on page 67. 3. Removing the air shroud on page 75 4. Removing the internal PERC riser on page 82 Steps 1. Using a Phillips #2 screwdriver, remove the screw that secures the PERC card to the internal PERC riser. 2. Pull the PERC card out of the connector on the internal PERC riser. Installing and removing system components 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 40. Installing internal PERC riser
5.
Connect the cables to the backplane and then route the cables to the cable guiding latch to close the latch.
Next steps
1.
Installing the air shroud
on page 77
2.
Follow the procedure listed in
After working inside your system
on page 67.
Removing the PERC card from the internal PERC riser
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Follow the procedure listed in
Before working inside your system
on page 67.
3.
Removing the air shroud
on page 75
4.
Removing the internal PERC riser
on page 82
Steps
1.
Using a Phillips #2 screwdriver, remove the screw that secures the PERC card to the internal PERC riser.
2.
Pull the PERC card out of the connector on the internal PERC riser.
Installing and removing system components
85