Dell PowerEdge R540 EMC Installation and Service Manual - Page 165

Installing system board, Next steps

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 165 highlights

Figure 128. Installing system board Next steps 1. Replace the following: a. Upgrading the Trusted Platform Module on page 167 b. Installing PERC card into the internal PERC riser on page 86 c. Optional internal USB memory key on page 147) d. USB 3.0 module (if applicable) e. IDSDM/vFlash module card f. All expansion cards and risers g. Processors and heat sink modules h. Processors blanks (if applicable) i. Memory modules j. LOM riser card k. Air shroud l. Drive cage (rear) (if applicable) 2. Reconnect all cables to the system board. NOTE: Ensure that the cables inside the system are routed along the chassis wall and secured using the cable securing bracket. 3. Follow the procedure listed in After working inside your system on page 67. 4. Ensure that you: a. Use the Easy Restore feature to restore the Service Tag. For more information, see the Restoring the service tag using Easy Restore section. b. If the Service Tag is not backed up in the backup flash device, enter the Service Tag manually. For more information, see the Manually update the Service Tag section. c. Update the BIOS and iDRAC versions. d. Re-enable the Trusted Platform Module (TPM). For more information, see the Upgrading the Trusted Platform Module on page 167 section. 5. Import your new or existing iDRAC Enterprise license. For more information, see Integrated Dell Remote Access Controller User's Guide, at www.dell.com/poweredgemanuals. Installing and removing system components 165

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 128. Installing system board
Next steps
1.
Replace the following:
a.
Upgrading the Trusted Platform Module
on page 167
b.
Installing PERC card into the internal PERC riser
on page 86
c.
Optional internal USB memory key
on page 147)
d.
USB 3.0 module (if applicable)
e.
IDSDM/vFlash module card
f.
All expansion cards and risers
g.
Processors and heat sink modules
h.
Processors blanks (if applicable)
i.
Memory modules
j.
LOM riser card
k.
Air shroud
l.
Drive cage (rear) (if applicable)
2.
Reconnect all cables to the system board.
NOTE:
Ensure that the cables inside the system are routed along the chassis wall and secured using the cable
securing bracket.
3.
Follow the procedure listed in
After working inside your system
on page 67.
4.
Ensure that you:
a.
Use the Easy Restore feature to restore the Service Tag. For more information, see the
Restoring the service tag using Easy
Restore
section.
b.
If the Service Tag is not backed up in the backup flash device, enter the Service Tag manually. For more information, see the
Manually update the Service Tag
section.
c.
Update the BIOS and iDRAC versions.
d.
Re-enable the Trusted Platform Module (TPM). For more information, see the
Upgrading the Trusted Platform Module
on page
167 section.
5.
Import your new or existing iDRAC Enterprise license.
For more information, see
Integrated Dell Remote Access Controller User's Guide
, at
www.dell.com/poweredgemanuals
.
Installing and removing system components
165