Dell PowerEdge R540 EMC Installation and Service Manual - Page 69

System cover, Removing the system cover

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Figure 24. Installing the front bezel with the LCD panel System cover NOTE: The system cover of 12 x 3.5-inch + 2 x 3.5-inch (rear) system is different from other systems. The cover has one additional mylar and foam layer on the front side of the system cover. Removing the system cover Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Turn off the system, including any attached peripherals. 3. Disconnect the system from the electrical outlet and disconnect the peripherals. Steps 1. Using a 1/4 inch flat head or a Phillips #2 screwdriver, rotate the latch release lock counter clockwise to the unlocked position. 2. Lift the latch till the system cover slides back and the tabs on the system cover disengage from the guide slots on the system. 3. Hold the cover on both sides, and lift the cover away from the system. Installing and removing system components 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 24. Installing the front bezel with the LCD panel
System cover
NOTE:
The system cover of 12 x 3.5-inch + 2 x 3.5-inch (rear) system is different from other systems. The cover has
one additional mylar and foam layer on the front side of the system cover.
Removing the system cover
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Turn off the system, including any attached peripherals.
3.
Disconnect the system from the electrical outlet and disconnect the peripherals.
Steps
1.
Using a 1/4 inch flat head or a Phillips #2 screwdriver, rotate the latch release lock counter clockwise to the unlocked position.
2.
Lift the latch till the system cover slides back and the tabs on the system cover disengage from the guide slots on the system.
3.
Hold the cover on both sides, and lift the cover away from the system.
Installing and removing system components
69