Dell PowerEdge R540 EMC Installation and Service Manual - Page 158

Installing power interposer board, Control panel, Removing the left control panel

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 158 highlights

Installing power interposer board Prerequisites Follow the safety guidelines listed in Safety instructions on page 66. Steps 1. Align the slots on the PIB with the hook on the PSU cage and slide it into place. 2. Using a Phillips #2 screwdriver, tighten the screw to secure the PIB to the system. 3. Route the cables and connect it to the system board. Figure 121. Installing power interposer board Next steps 1. Installing a processor and heat sink module on page 108 2. Installing the air shroud on page 77 3. Follow the procedure listed in After working inside your system on page 67. Control panel Removing the left control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Follow the procedure listed in Before working inside your system on page 67. 3. Removing the air shroud on page 75 4. Removing the PERC card from the internal PERC riser on page 85 158 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Installing power interposer board
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 66.
Steps
1.
Align the slots on the PIB with the hook on the PSU cage and slide it into place.
2.
Using a Phillips #2 screwdriver, tighten the screw to secure the PIB to the system.
3.
Route the cables and connect it to the system board.
Figure 121. Installing power interposer board
Next steps
1.
Installing a processor and heat sink module
on page 108
2.
Installing the air shroud
on page 77
3.
Follow the procedure listed in
After working inside your system
on page 67.
Control panel
Removing the left control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Follow the procedure listed in
Before working inside your system
on page 67.
3.
Removing the air shroud
on page 75
4.
Removing the PERC card from the internal PERC riser
on page 85
158
Installing and removing system components