Dell PowerEdge R540 EMC Installation and Service Manual - Page 160

Removing the right control panel

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 160 highlights

Figure 123. Installing left control panel Next steps 1. Installing the air shroud on page 77 2. Installing PERC card into the internal PERC riser on page 86 3. Follow the procedure listed in After working inside your system on page 67. Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Follow the procedure listed in Before working inside your system on page 67. 3. Removing the PERC card from the internal PERC riser on page 85 Steps 1. Lift the cable latch and disconnect the control panel cable from the connector on the system board. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. You must route the cables properly when you replace them to prevent the cables from being pinched or crimped. 2. Using Phillips #1 screwdriver, remove the screws that secure the right control panel assembly to the system. 160 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 123. Installing left control panel
Next steps
1.
Installing the air shroud
on page 77
2.
Installing PERC card into the internal PERC riser
on page 86
3.
Follow the procedure listed in
After working inside your system
on page 67.
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Follow the procedure listed in
Before working inside your system
on page 67.
3.
Removing the PERC card from the internal PERC riser
on page 85
Steps
1.
Lift the cable latch and disconnect the control panel cable from the connector on the system board.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. You must route
the cables properly when you replace them to prevent the cables from being pinched or crimped.
2.
Using Phillips #1 screwdriver, remove the screws that secure the right control panel assembly to the system.
160
Installing and removing system components