Dell PowerEdge R540 EMC Installation and Service Manual - Page 119

Removing expansion card from the system board

Get Dell PowerEdge R540 PDF manuals and user guides View all Dell PowerEdge R540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Figure 76. Installing expansion card into butterfly riser Next steps 1. If applicable, connect the cables to the expansion card. 2. If applicable, install air shroud. 3. Follow the procedure listed in After working inside your system on page 67. 4. Install any device drivers required for the card as described in the documentation for the card. Removing expansion card from the system board Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 66. 2. Follow the procedure listed in Before working inside your system on page 67. 3. Disconnect any cables connected to the expansion card. Steps 1. Pull and lift up the expansion card retention latch lock to open. 2. Hold the expansion card by the edge and pull the card to disconnect from the system board connector. Installing and removing system components 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Figure 76. Installing expansion card into butterfly riser
Next steps
1.
If applicable, connect the cables to the expansion card.
2.
If applicable,
install air shroud
.
3.
Follow the procedure listed in
After working inside your system
on page 67.
4.
Install any device drivers required for the card as described in the documentation for the card.
Removing expansion card from the system board
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 66.
2.
Follow the procedure listed in
Before working inside your system
on page 67.
3.
Disconnect any cables connected to the expansion card.
Steps
1.
Pull and lift up the expansion card retention latch lock to open.
2.
Hold the expansion card by the edge and pull the card to disconnect from the system board connector.
Installing and removing system components
119