Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 124

Optional IDSDM or vFlash module, Removing the optional IDSDM or vFlash card

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Figure 69. Installing the M.2 SSD module a. module connector (2) b. screws (2) c. modules (2) Next steps 1. Install the BOSS card. NOTE: Installing the BOSS card is similar to installing the expansion card riser. 2. Install the air shroud. 3. Follow the procedure listed in After working inside your system on page 72. Optional IDSDM or vFlash module NOTE: The write-protect switch is on the IDSDM or vFlash module. Removing the optional IDSDM or vFlash card Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 71. 2. Follow the procedure listed in After working inside your system on page 72. 3. If you are replacing the IDSDM/vFlash card, remove the MicroSD cards. NOTE: Temporarily label each MicroSD card with its corresponding slot number after removal. Steps 1. Locate the IDSDM/vFlash connector on the system board. To locate IDSDM/vFlash connector, see the System board jumpers and connectors section. 2. Holding the pull tab, lift the IDSDM/vFlash card out of the system. 124 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Figure 69. Installing the M.2 SSD module
a.
module connector (2)
b.
screws (2)
c.
modules (2)
Next steps
1.
Install the BOSS card.
NOTE:
Installing the BOSS card is similar to installing the expansion card riser.
2.
Install the air shroud
.
3.
Follow the procedure listed in
After working inside your system
on page 72.
Optional IDSDM or vFlash module
NOTE:
The write-protect switch is on the IDSDM or vFlash module.
Removing the optional IDSDM or vFlash card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 71.
2.
Follow the procedure listed in
After working inside your system
on page 72.
3.
If you are replacing the IDSDM/vFlash card, remove the MicroSD cards.
NOTE:
Temporarily label each MicroSD card with its corresponding slot number after removal.
Steps
1.
Locate the IDSDM/vFlash connector on the system board.
To locate IDSDM/vFlash connector, see the
System board jumpers and connectors
section.
2.
Holding the pull tab, lift the IDSDM/vFlash card out of the system.
124
Installing and removing system components