Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 165

Removing the right control panel

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 165 highlights

Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 71. 2. Follow the procedure listed in Before working inside your system on page 72. 3. For ease of removal of the right control panel, remove the cooling fan #8 to access the cable latch. Steps 1. Lift the cable latch and disconnect the control panel cable from the connector on the system board. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. You must route the cables properly when you replace them to prevent the cables from being pinched or crimped. 2. Using a Phillips #1 screwdriver, remove the screws that secure the cable cover to the system. Figure 117. Removing the cable cover 3. Using a Phillips #1 screwdriver, remove the screw that secures the control panel to the system. Figure 118. Removing right control panel 4. Holding by the sides, remove the right control panel away from the system. 5. Holding the control panel by its sides, remove the control panel away from the system. Next steps Install the right control panel. Installing and removing system components 165

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 71.
2.
Follow the procedure listed in
Before working inside your system
on page 72.
3.
For ease of removal of the right control panel,
remove the cooling fan
#8 to access the cable latch.
Steps
1.
Lift the cable latch and disconnect the control panel cable from the connector on the system board.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. You must route
the cables properly when you replace them to prevent the cables from being pinched or crimped.
2.
Using a Phillips #1 screwdriver, remove the screws that secure the cable cover to the system.
Figure 117. Removing the cable cover
3.
Using a Phillips #1 screwdriver, remove the screw that secures the control panel to the system.
Figure 118. Removing right control panel
4.
Holding by the sides, remove the right control panel away from the system.
5.
Holding the control panel by its sides, remove the control panel away from the system.
Next steps
Install the right control panel.
Installing and removing system components
165