Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 128

Network daughter card, Removing the network daughter card

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

Figure 73. Installing the MicroSD card Next steps Follow the procedure listed in After working inside your system on page 72. Network daughter card Removing the network daughter card Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 71. 2. Follow the procedure listed in After working inside your system on page 72. 3. Remove the expansion card riser 2 or the rear drive cage, depending on the configuration of your system. Steps 1. Using a Phillips #2 screwdriver, loosen the captive screws that secure the network daughter card (NDC) to the system board. 2. Hold the NDC by the edges on either side of the touch points, and lift to remove it from the connector on the system board. 3. Slide the NDC towards the front of the system until the Ethernet connectors are clear of the slot in the back panel. 128 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Figure 73. Installing the MicroSD card
Next steps
Follow the procedure listed in
After working inside your system
on page 72.
Network daughter card
Removing the network daughter card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 71.
2.
Follow the procedure listed in
After working inside your system
on page 72.
3.
Remove the expansion card riser 2 or the rear drive cage, depending on the configuration of your system.
Steps
1.
Using a Phillips #2 screwdriver, loosen the captive screws that secure the network daughter card (NDC) to the system board.
2.
Hold the NDC by the edges on either side of the touch points, and lift to remove it from the connector on the system board.
3.
Slide the NDC towards the front of the system until the Ethernet connectors are clear of the slot in the back panel.
128
Installing and removing system components