Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 127

Installing the MicroSD card

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Figure 72. Removing the MicroSD card Next steps 1. Follow the procedure listed in After working inside your system on page 72. 2. Install a MicroSD card. Installing the MicroSD card Prerequisites Follow the safety guidelines listed in Safety instructions on page 71. NOTE: To use an MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup. NOTE: If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. Steps 1. Locate the MicroSD card connector on the IDSDM/vFlash module. Orient the MicroSD card appropriately and insert the contact-pin end of the card into the slot. To locate IDSDM/vFlash, see the System board jumpers and connectors section. NOTE: The slot is keyed to ensure correct insertion of the card. 2. Press the card into the card slot to lock it into place. Installing and removing system components 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Figure 72. Removing the MicroSD card
Next steps
1.
Follow the procedure listed in
After working inside your system
on page 72.
2.
Install a MicroSD card.
Installing the MicroSD card
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 71.
NOTE:
To use an MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup.
NOTE:
If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked
on the cards during removal.
Steps
1.
Locate the MicroSD card connector on the IDSDM/vFlash module. Orient the MicroSD card appropriately and insert the contact-pin
end of the card into the slot. To locate IDSDM/vFlash, see the
System board jumpers and connectors
section.
NOTE:
The slot is keyed to ensure correct insertion of the card.
2.
Press the card into the card slot to lock it into place.
Installing and removing system components
127