Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 148

Installing the USB module, VGA module, Removing the VGA module

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Installing the USB module Prerequisites Follow the safety guidelines listed in Safety instructions on page 71. NOTE: The procedure to install the USB 3.0 and USB 2.0 modules is similar. Steps 1. Route the USB cable on the USB module, through the USB slot on the front panel. 2. Insert the USB module into the slot on the front panel. 3. Align the screw on the module with the screw hole on the system. 4. Using the Phillips #1 screwdriver, replace the screw to secure the module to the system. 5. Route the USB cable and connect it to the USB connector on the system board. For more information, see the System board jumpers and connecters section. Figure 101. Installing the USB module Next steps 1. Install the air shroud. 2. Install the backplane cover. 3. Follow the procedure listed in After working inside your system on page 72. VGA module Removing the VGA module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 71. 2. Follow the procedure listed in Before working inside your system on page 72. 3. Remove the front bezel 148 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Installing the USB module
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 71.
NOTE:
The procedure to install the USB 3.0 and USB 2.0 modules is similar.
Steps
1.
Route the USB cable on the USB module, through the USB slot on the front panel.
2.
Insert the USB module into the slot on the front panel.
3.
Align the screw on the module with the screw hole on the system.
4.
Using the Phillips #1 screwdriver, replace the screw to secure the module to the system.
5.
Route the USB cable and connect it to the USB connector on the system board. For more information, see the System board jumpers
and connecters section.
Figure 101. Installing the USB module
Next steps
1.
Install the air shroud
.
2.
Install the backplane cover
.
3.
Follow the procedure listed in
After working inside your system
on page 72.
VGA module
Removing the VGA module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 71.
2.
Follow the procedure listed in
Before working inside your system
on page 72.
3.
Remove the front bezel
148
Installing and removing system components