Dell PowerEdge R640 EMC PowerEdge R640 Installation and Service Manual - Page 130

Integrated storage controller card

Get Dell PowerEdge R640 PDF manuals and user guides View all Dell PowerEdge R640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Next steps 1. Install the expansion card riser 2 or the rear drive cage, depending on the configuration of your system. 2. Follow the procedure listed in After working inside your system on page 72. Integrated storage controller card Removing the integrated storage controller card Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 71. 2. Follow the procedure listed in After working inside your system on page 72. 3. Remove the air shroud. Steps 1. Using Phillips #2 screwdriver, loosen the screws that secure the integrated storage controller cable to the connector on the system board. 2. Lift the integrated storage controller cable to disconnect it from the connector on the system board. Figure 76. Removing the integrated storage controller cable 3. Lift one end of the card and angle it to disengage the card from the card holder on the system board. 4. Lift the card out of the system. 130 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
Next steps
1.
Install the expansion card riser 2 or the rear drive cage, depending on the configuration of your system.
2.
Follow the procedure listed in
After working inside your system
on page 72.
Integrated storage controller card
Removing the integrated storage controller card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 71.
2.
Follow the procedure listed in
After working inside your system
on page 72.
3.
Remove the air shroud
.
Steps
1.
Using Phillips #2 screwdriver, loosen the screws that secure the integrated storage controller cable to the connector on the system
board.
2.
Lift the integrated storage controller cable to disconnect it from the connector on the system board.
Figure 76. Removing the integrated storage controller cable
3.
Lift one end of the card and angle it to disengage the card from the card holder on the system board.
4.
Lift the card out of the system.
130
Installing and removing system components