Dell PowerEdge T110 Hardware Owner's Manual - Page 77

Replace the expansion card stabilizer. See Installing the Expansion Card - inside

Get Dell PowerEdge T110 PDF manuals and user guides View all Dell PowerEdge T110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

4 Disconnect all cables from the card. 5 Open the expansion-card latch. See Figure 3-13. 6 Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector. 7 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch. NOTE: Filler brackets must be installed over empty expansion card slots to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 8 Replace the expansion card stabilizer. See "Installing the Expansion Card Stabilizer" on page 72. 9 Close the system. See "Closing the System" on page 58. 10 Reconnect the system and peripherals to their power sources, and turn them on. 11 Remove the card's device driver from the operating system. Installing System Components 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Installing System Components
77
4
Disconnect all cables from the card.
5
Open the expansion-card latch. See Figure 3-13.
6
Grasp the expansion card by its edges, and carefully remove it from the
expansion-card connector.
7
If you are removing the card permanently, install a metal filler bracket over
the empty expansion slot opening and close the expansion-card latch.
NOTE:
Filler brackets must be installed over empty expansion card slots to
maintain Federal Communications Commission (FCC) certification of the
system. The brackets also keep dust and dirt out of the system and aid in
proper cooling and airflow inside the system.
8
Replace the expansion card stabilizer. See "Installing the Expansion Card
Stabilizer" on page 72.
9
Close the system. See "Closing the System" on page 58.
10
Reconnect the system and peripherals to their power sources, and turn
them on.
11
Remove the card’s device driver from the operating system.