Epson F6200 User Manual - Page 82

Moving or Transporting the Product, Prepare to Move the Product, Setting Up the Product After Moving

Get Epson F6200 PDF manuals and user guides View all Epson F6200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Moving or Transporting the Product When moving the product, see these sections to prepare and move the product, and set it back up after moving it. If you need to transport the product a long distance, contact Epson support. Prepare to Move the Product Setting Up the Product After Moving Prepare to Move the Product Do the following before moving the product: 1. Remove any loaded media. 2. Turn off the product. 3. Remove the waste ink bottle. 4. Remove all cables. 5. Release the locks on the product stand. Caution: Roll the product for only a short distance over a level floor. Do not tilt the product more than 10° in any direction or the product may fall over. Parent topic: Moving or Transporting the Product Related tasks Removing Media Replacing the Waste Ink Bottle Setting Up the Product After Moving Follow these steps to set up the product after moving it. 1. Verify that the location is suitable for installation. 2. Install the waste ink bottle. 3. Connect the power cable to an electrical outlet and turn on the printer. 4. Load media in the product. 5. Perform a nozzle check and confirm that there are no clogged nozzles. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Moving or Transporting the Product
When moving the product, see these sections to prepare and move the product, and set it back up after
moving it.
If you need to transport the product a long distance, contact Epson support.
Prepare to Move the Product
Setting Up the Product After Moving
Prepare to Move the Product
Do the following before moving the product:
1. Remove any loaded media.
2. Turn off the product.
3. Remove the waste ink bottle.
4. Remove all cables.
5. Release the locks on the product stand.
Caution:
Roll the product for only a short distance over a level floor. Do not tilt the product more than
10° in any direction or the product may fall over.
Parent topic:
Moving or Transporting the Product
Related tasks
Removing Media
Replacing the Waste Ink Bottle
Setting Up the Product After Moving
Follow these steps to set up the product after moving it.
1.
Verify that the location is suitable for installation.
2.
Install the waste ink bottle.
3.
Connect the power cable to an electrical outlet and turn on the printer.
4.
Load media in the product.
5.
Perform a nozzle check and confirm that there are no clogged nozzles.
82