HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 23

Accessing a Pedestal-Mounted Server, Pedestal-Mounted Server

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Installing the System Installing Additional Components Inserting the Server Into the Rack To insert the server into the rack, follow these steps: Step 1. Press the rail clips on either side of the server inward and push the server into the rack until it stops. Step 2. Replace the T-25 screws that fasten the server to the rack. Accessing a Pedestal-Mounted Server The HP 9000 rp4410 and rp4440 servers are also designed to be mounted in a pedestal (rackless). You do not need to remove the pedestal from the server to gain access to internal components. The front bezel, front cover, and top cover can be removed with the pedestal attached to the server. WARNING Ensure that the server is properly grounded when performing remove and replace procedures. Use an antistatic wrist strap and grounding mat similar to those found in the HP Electrically Conductive Field Service Kit. Figure 1-5 shows a pedestal-mounted server. Figure 1-5 Pedestal-Mounted Server Chapter 1 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
23
Inserting the Server Into the Rack
To insert the server into the rack, follow these steps:
Step 1.
Press the rail clips on either side of the server inward and push the server into the rack until it
stops.
Step 2.
Replace the T-25 screws that fasten the server to the rack.
Accessing a Pedestal-Mounted Server
The HP 9000 rp4410 and rp4440 servers are also designed to be mounted in a pedestal (rackless). You do not
need to remove the pedestal from the server to gain access to internal components. The front bezel, front
cover, and top cover can be removed with the pedestal attached to the server.
WARNING
Ensure that the server is properly grounded when performing remove and replace
procedures. Use an antistatic wrist strap and grounding mat similar to those found
in the HP Electrically Conductive Field Service Kit.
Figure 1-5 shows a pedestal-mounted server.
Figure 1-5
Pedestal-Mounted Server