HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 68

Removing the SCSI Jumper Cable, Step 2.

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Installing the System Installing Additional Components Figure 1-36 Removing the SCSI Jumper Cable Step 2. Install the duplex board in the SCSI connector located nearest the disk drive cage. a. Align the bracket tabs with the slots on the side of the disk drive cage. b. Press the bracket against the disk drive cage until the bracket locks into place. c. Align the connector of the duplex board with the connector on the SCSI backplane. d. Press the board connector into the backplane connector. NOTE In simplex mode, both hard disk drives in slot 0 and slot 1 are driven by SCSI channel A. When the duplex board is installed, the slot 1 hard disk drive is now driven by SCSI channel B. If HP-UX was previously installed and whole disk vxfs was not used, the system no longer boots. 68 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
68
Figure 1-36 Removing the SCSI Jumper Cable
Step 2.
Install the duplex board in the SCSI connector located nearest the disk drive cage.
a.
Align the bracket tabs with the slots on the side of the disk drive cage.
b.
Press the bracket against the disk drive cage until the bracket locks into place.
c.
Align the connector of the duplex board with the connector on the SCSI backplane.
d.
Press the board connector into the backplane connector.
NOTE
In simplex mode, both hard disk drives in slot 0 and slot 1 are driven by SCSI
channel A. When the duplex board is installed, the slot 1 hard disk drive is now
driven by SCSI channel B. If HP-UX was previously installed and whole disk vxfs
was not used, the system no longer boots.