HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 30

Removing and Replacing the Front Cover, Step 4., Replacing the Front Cover

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Installing the System Installing Additional Components Figure 1-12 Removing and Replacing the Front Cover Thumbscrews Step 4. Raise the cover slightly, and pull the cover toward the front of the server to free the tabs from the slots in the center of the chassis. Replacing the Front Cover To replace the front cover, follow these steps: Step 1. Align the tabs at the rear of the front cover with the corresponding slots in the chassis and fully seat the tabs into the slots. Step 2. Tighten the four thumbscrews securely. Step 3. Replace the front bezel. (See "Replacing the Front Bezel" on page 29.) Removing the Top Cover To remove the top cover, follow these steps: Step 1. If rack-mounted, slide the server out from the rack until it stops. (See "Extend the Server from the Rack" on page 22.) Step 2. Loosen the two captive thumbscrews that hold the top cover in place. Step 3. Pull the cover toward the rear of the server to free the tabs from the slots in the center of the chassis and lift the cover straight up. 30 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
30
Figure 1-12 Removing and Replacing the Front Cover
Step 4.
Raise the cover slightly, and pull the cover toward the front of the server to free the tabs from the
slots in the center of the chassis.
Replacing the Front Cover
To replace the front cover, follow these steps:
Step 1.
Align the tabs at the rear of the front cover with the corresponding slots in the chassis and fully
seat the tabs into the slots.
Step 2.
Tighten the four thumbscrews securely.
Step 3.
Replace the front bezel. (See “Replacing the Front Bezel” on page 29.)
Removing the Top Cover
To remove the top cover, follow these steps:
Step 1.
If rack-mounted, slide the server out from the rack until it stops. (See “Extend the Server from the
Rack” on page 22.)
Step 2.
Loosen the two captive thumbscrews that hold the top cover in place.
Step 3.
Pull the cover toward the rear of the server to free the tabs from the slots in the center of the
chassis and lift the cover straight up.
Thumbscrews