HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 65

Table 1-12, Hot-Pluggable LED Descriptions, Understanding LEDs and Hardware Errors

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Installing the System Installing Additional Components IMPORTANT When inserting the PCI/PCI-X card, be careful you do not accidentally touch an Attention button on the other OLX dividers. This initiates an undesired shutdown of another PCI/PCI-X card/slot. If you accidentally initiate slot shutdown, push the Attention button again within five seconds to cancel the shutdown. NOTE Ensure that you fully seat the card into the slot, or undesired results can occur after power is reapplied to the slot. Step 11. If the PCI/PCI-X card is full size, close the slider gate latch to secure the end of the card. (Figure 1-33) Step 12. Push the MRL down until it seats against the chassis wall. Step 13. Turn the PCI/PCI-X card latch on the chassis to the closed position. This locks the PCI/PCI-X card into its slot and the MRL into the closed position. Step 14. Press the Attention button. The power LED starts to blink. Step 15. Wait for the power LED to stop blinking. The PCI/PCI-X card is now active. Step 16. Reconnect all cables. Step 17. Replace the top cover. (See "Replacing the Top Cover" on page 31.) Step 18. Push the server all the way back into the rack until it stops. Understanding LEDs and Hardware Errors Table 1-12 describes the hot-pluggable LED error conditions. Table 1-12 Hot-Pluggable LED Descriptions Power LED (Green) Condition On Blinking Off Attention LED (Amber) Condition On Blinking Off Description PCI/PCI-X slot is powered on Hot-pluggable operation in progress. Do not touch the slot PCI/PCI-X slot is powered off Description Hardware operational fault NOTE: If the slot is powered on, it does not power off. If the slot is powered off, it does not power on Slot location is being indicated If power to the slot is on, the slot is functioning normally Chapter 1 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
65
IMPORTANT
When inserting the PCI/PCI-X card, be careful you do not accidentally touch an
Attention
button on the other OLX dividers. This initiates an undesired shutdown of
another PCI/PCI-X card/slot. If you accidentally initiate slot shutdown, push the
Attention
button again within five seconds to cancel the shutdown.
NOTE
Ensure that you fully seat the card into the slot, or undesired results can occur after
power is reapplied to the slot.
Step 11.
If the PCI/PCI-X card is full size, close the slider gate latch to secure the end of the card.
(Figure 1-33)
Step 12.
Push the MRL down until it seats against the chassis wall.
Step 13.
Turn the PCI/PCI-X card latch on the chassis to the closed position. This locks the PCI/PCI-X card
into its slot and the MRL into the closed position.
Step 14.
Press the
Attention
button. The power LED starts to blink.
Step 15.
Wait for the power LED to stop blinking. The PCI/PCI-X card is now active.
Step 16.
Reconnect all cables.
Step 17.
Replace the top cover. (See “Replacing the Top Cover” on page 31.)
Step 18.
Push the server all the way back into the rack until it stops.
Understanding LEDs and Hardware Errors
Table 1-12 describes the hot-pluggable LED error conditions.
Table 1-12
Hot-Pluggable LED Descriptions
Power LED (Green)
Condition
Description
On
PCI/PCI-X slot is powered on
Blinking
Hot-pluggable operation in progress. Do not touch the slot
Off
PCI/PCI-X slot is powered off
Attention LED (Amber)
Condition
Description
On
Hardware operational fault
NOTE:
If the slot is powered on, it does not power off. If the
slot is powered off, it does not power on
Blinking
Slot location is being indicated
Off
If power to the slot is on, the slot is functioning normally