HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 41

Metal Cover in Unused Slot P1, Step 1.

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Installing the System Installing Additional Components CAUTION If the system is powered off, install the hot-swappable power supply into the server before attaching the new power cord at the rear of the system. Failure to observe this caution results in damage to the server. To install a hot-swappable power supply, follow these steps: Step 1. If rack-mounted, slide the server out from the rack until it stops. (See "Extend the Server from the Rack" on page 22.) Step 2. Remove the cable management arm from the rack slide nearest the power supplies. The cable management arm does not need to be completely removed, but moved just enough to enable access to the power supplies. Step 3. Remove the metal cover from slot P1. Grasp the metal cover and pull straight out. Figure 1-19 Metal Cover in Unused Slot P1 Step 4. Supporting the power supply with both hands, slide it into slot P1 until it plugs into the socket on the internal power supply board. Hand tighten the thumbscrew. Step 5. Install the power cord into the power supply socket and secure it to the power cord bracket. Step 6. Apply power (200 - 240 VAC) to the new power supply. The LED immediately turns on. Chapter 1 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
41
CAUTION
If the system is powered off, install the hot-swappable power supply into the server before
attaching the new power cord at the rear of the system. Failure to observe this caution results
in damage to the server.
To install a hot-swappable power supply, follow these steps:
Step 1.
If rack-mounted, slide the server out from the rack until it stops. (See “Extend the Server from the
Rack” on page 22.)
Step 2.
Remove the cable management arm from the rack slide nearest the power supplies. The cable
management arm does not need to be completely removed, but moved just enough to enable access
to the power supplies.
Step 3.
Remove the metal cover from slot P1. Grasp the metal cover and pull straight out.
Figure 1-19 Metal Cover in Unused Slot P1
Step 4.
Supporting the power supply with both hands, slide it into slot P1 until it plugs into the socket on
the internal power supply board. Hand tighten the thumbscrew.
Step 5.
Install the power cord into the power supply socket and secure it to the power cord bracket.
Step 6.
Apply power (200 - 240 VAC) to the new power supply. The LED immediately turns on.