HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 64

Step 8., Step 9., Step 10., Step 11., Step 1., Step 2., Step 3., Step 4., Step 5., Step 6., Step 7

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Installing the System Installing Additional Components Step 8. Turn the PCI/PCI-X card latch to the closed position to capture the PCI/PCI-X card and MRL into the closed position. Step 9. Press the Attention button . The power LED starts to blink. Wait until the power LED goes from blinking to steady on. NOTE After pushing the Attention button, you have five seconds to cancel the operation by pushing the Attention button again. After five seconds, pressing the Attention button initiates slot power off for OLR of the card. Step 10. Replace the top cover. (See "Replacing the Top Cover" on page 31.) Step 11. Push the server all the way back into the rack until it stops. OLR CAUTION For HP-UX 11i v1 (and higher), you must replace an existing card with an identical card. To remove and replace a PCI/PCI-X card into a populated slot, follow these steps: Step 1. If rack-mounted, slide the server out from the rack until it stops. (See "Extend the Server from the Rack" on page 22.) Step 2. Remove the top cover from the chassis. (See "Removing the Top Cover" on page 30.) Step 3. Disconnect all external and internal cables attached to the PCI card in the side service bay. Step 4. Press the Attention button located on the OLX divider that controls the affected slot. The power LED starts to blink. Wait until the power LED goes from blinking to steady off. NOTE After pushing the Attention button, you have five seconds to cancel the operation by pushing the Attention button again. Step 5. Turn the PCI/PCI-X card latch approximately 45 degrees on the chassis until the MRL is free to pull up. Step 6. Pull up on the MRL located on the OLX divider to turn off power to the slot. (Figure 1-33) Step 7. Turn the PCI/PCI-X card latch on the chassis approximately 90 degrees to completely expose the PCI/PCI-X bulkhead. Step 8. If the PCI/PCI-X card is full size, open the slider gate latch to release the end of the card. (Figure 1-35) Step 9. Grasp the top edge of the PCI/PCI-X card and remove it from the slot. NOTE There is no ejection lever to remove PCI/PCI-X cards as on previous server models. You must remove the PCI/PCI-X card manually. Cutouts in the OLX dividers enable access for grasping PCI/PCI-X cards. Step 10. Insert the new PCI/PCI-X card into the powered off slot. (Figure 1-34) 64 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
64
Step 8.
Turn the PCI/PCI-X card latch to the closed position to capture the PCI/PCI-X card and MRL into
the closed position.
Step 9.
Press the
Attention
button . The power LED starts to blink. Wait until the power LED goes from
blinking to steady on.
NOTE
After pushing the
Attention
button, you have five seconds to cancel the operation by
pushing the
Attention
button again. After five seconds, pressing the
Attention
button
initiates slot power off for OLR of the card.
Step 10.
Replace the top cover. (See “Replacing the Top Cover” on page 31.)
Step 11.
Push the server all the way back into the rack until it stops.
OLR
CAUTION
For HP-UX 11i v1 (and higher), you must replace an existing card with an identical card.
To remove and replace a PCI/PCI-X card into a populated slot, follow these steps:
Step 1.
If rack-mounted, slide the server out from the rack until it stops. (See “Extend the Server from the
Rack” on page 22.)
Step 2.
Remove the top cover from the chassis. (See “Removing the Top Cover” on page 30.)
Step 3.
Disconnect all external and internal cables attached to the PCI card in the side service bay.
Step 4.
Press the
Attention
button located on the OLX divider that controls the affected slot. The power
LED starts to blink. Wait until the power LED goes from blinking to steady off.
NOTE
After pushing the
Attention
button, you have five seconds to cancel the operation by
pushing the
Attention
button again.
Step 5.
Turn the PCI/PCI-X card latch approximately 45 degrees on the chassis until the MRL is free to
pull up.
Step 6.
Pull up on the MRL located on the OLX divider to turn off power to the slot. (Figure 1-33)
Step 7.
Turn the PCI/PCI-X card latch on the chassis approximately 90 degrees to completely expose the
PCI/PCI-X bulkhead.
Step 8.
If the PCI/PCI-X card is full size, open the slider gate latch to release the end of the card.
(Figure 1-35)
Step 9.
Grasp the top edge of the PCI/PCI-X card and remove it from the slot.
NOTE
There is no ejection lever to remove PCI/PCI-X cards as on previous server models.
You must remove the PCI/PCI-X card manually. Cutouts in the OLX dividers enable
access for grasping PCI/PCI-X cards.
Step 10.
Insert the new PCI/PCI-X card into the powered off slot. (Figure 1-34)