HP 9000 rp4410-4 Installation Guide, Sixth Edition - HP 9000 rp4410/rp4440 - Page 55

Removing the Memory Extender Board, Removing a Memory Extender Board

Get HP 9000 rp4410-4 PDF manuals and user guides View all HP 9000 rp4410-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Removing a Memory Extender Board The memory extender boards is located under the front cover. Installing the System Installing Additional Components WARNING Ensure that the system is powered off and all power sources have been disconnected from the server prior to attempting this procedure. Voltages are present at various locations within the server whenever an ac power source is connected. This voltage is present even when the main power switch is in the off position. Failure to observe this warning can result in personal injury or damage to equipment. To remove a memory extender board, follow these steps: Step 1. If rack-mounted, slide the server out from the rack until it stops. (See "Extend the Server from the Rack" on page 22.) Step 2. Remove the front bezel from the chassis. (See "Removing the Front Bezel" on page 28.) Step 3. Remove the front cover from the chassis. (See "Removing the Front Cover" on page 29.) Step 4. Press the latches on the extraction levers located on each side of the memory extender board. Step 5. Pull on the extraction levers to unplug the memory extender board from the socket located on the midplane riser board and remove the memory extender board from the chassis. Figure 1-30 Removing the Memory Extender Board Chapter 1 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Installing the System
Installing Additional Components
Chapter 1
55
Removing a Memory Extender Board
The memory extender boards is located under the front cover.
WARNING
Ensure that the system is powered off and all power sources have been disconnected
from the server prior to attempting this procedure.
Voltages are present at various locations within the server whenever an ac power
source is connected. This voltage is present even when the main power switch is in
the off position.
Failure to observe this warning can result in personal injury or damage to
equipment.
To remove a memory extender board, follow these steps:
Step 1.
If rack-mounted, slide the server out from the rack until it stops. (See “Extend the Server from the
Rack” on page 22.)
Step 2.
Remove the front bezel from the chassis. (See “Removing the Front Bezel” on page 28.)
Step 3.
Remove the front cover from the chassis. (See “Removing the Front Cover” on page 29.)
Step 4.
Press the latches on the extraction levers located on each side of the memory extender board.
Step 5.
Pull on the extraction levers to unplug the memory extender board from the socket located on the
midplane riser board and remove the memory extender board from the chassis.
Figure 1-30 Removing the Memory Extender Board