HP LH4r HP Netserver LPr Installation Guide - Page 106

Error Message Is Displayed

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Chapter 13 Troubleshooting 5. Restart the system. If the system does not function, refer to one of the following sections, depending upon whether an error message is displayed or not displayed: 6 If the system still will not restart, press the [F2] key during boot to view system configuration information. Press the [F10] function key to exit, and answer Yes to save the changes. If necessary, you can use a hardware switch to clear the system configuration memory and restart the system, as described in "Clearing the System Configuration" in this chapter. Error Message Is Displayed There are two kinds of error messages that may prevent the HP NetServer LPr from booting. These are: • Highlighted error messages (white text on gray background). Press ENTER to see a definition of the message and what action to take to remedy the problem. • Error messages displayed in normal video. If an HP NetServer configuration error is reported during the startup routine, clear the system configuration memory and reconfigure as described under "Clearing the System Configuration" later in this chapter, then restart the HP NetServer LPr. Power-On System Hardware Test Error Messages If an error occurs during the power-on system hardware test (POST) when the HP NetServer LPr starts, press [Enter] to display details of the error. Follow the instructions on the screen. Correct the error before proceeding, even if the HP NetServer LPr appears to start successfully. If the HP NetServer LPr starts, but the power-on system hardware test still reports an error message, clear the system configuration memory as described in "Clearing the System Configuration" in this chapter. The following table describes common errors and the corrective action you may take to remedy the problem: 98

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 13
Troubleshooting
98
5.
Restart the system. If the system does not function, refer to one of the
following sections, depending upon whether an error message is displayed
or not displayed:
6
If the system still will not restart, press the [F2] key during boot to view
system configuration information. Press the [F10] function key to exit,
and answer
Yes
to save the changes. If necessary, you can use a hardware
switch to clear the system configuration memory and restart the system, as
described in "Clearing the System Configuration" in this chapter.
Error Message Is Displayed
There are two kinds of error messages that may prevent the HP NetServer LPr
from booting. These are:
•
Highlighted error messages (white text on gray background). Press
ENTER to see a definition of the message and what action to take to
remedy the problem.
•
Error messages displayed in normal video.
If an HP NetServer configuration error is reported during the startup routine,
clear the system configuration memory and reconfigure as described under
"Clearing the System Configuration" later in this chapter, then restart the HP
NetServer LPr.
Power-On System Hardware Test Error Messages
If an error occurs during the power-on system hardware test (POST) when the HP
NetServer LPr starts, press [Enter]
to display details of the error. Follow the
instructions on the screen. Correct the error before proceeding, even if the HP
NetServer LPr appears to start successfully.
If the HP NetServer LPr starts, but the power-on system hardware test still
reports an error message, clear the system configuration memory as described in
"Clearing the System Configuration" in this chapter.
The following table describes common errors and the corrective action you may
take to remedy the problem: