HP LH4r HP Netserver LPr Installation Guide - Page 50

Refer to Installing Mass Storage Devices, and see

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter 7 Installing Additional Boards Figure 7-2. Remove PCI Card Access Panel 6. Apply pressure at the top of the PCI access cover to pop it out. 7. Read the documentation that is included with the PCI card. Note any special instructions. NOTE Adding a PCI-to-PCI bridge card to the HP NetServer may alter the server's boot order. This boot order can be changed using the SETUP utility (press [F2] during the boot process). Refer to Chapter 4, "Installing Mass Storage Devices," and see the subsection, "Boot Device Priority." 8. Identify the PCI slot number to be used. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 7
Installing Additional Boards
42
Figure 7-2. Remove PCI Card Access Panel
6.
Apply pressure at the top of the PCI access cover to pop it out.
7.
Read the documentation that is included with the PCI card. Note any
special instructions.
NOTE
Adding a PCI-to-PCI bridge card to the HP NetServer may
alter the server’s boot order. This boot order can be changed
using the SETUP utility (press [F2] during the boot process).
Refer to Chapter 4, "Installing Mass Storage Devices," and see
the subsection, "Boot Device Priority."
8.
Identify the PCI slot number to be used.