HP LH4r HP Netserver LPr Installation Guide - Page 39

Installing Additional Memory

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 5 Installing Additional Memory Introduction The NetServer LPr's main memory is implemented with 5V SDRAM DIMMs (Dual In-Line Memory Modules). The NetServer LPr ships with at least 64 MB of main memory and supports up to 1 GB. Memory is available in the following DIMM capacities: 64, 128, and 256 MB. There are four DIMM sockets on the system board. See Figure 5-1 for socket location. DIMMs may be installed in any combination in any socket. However, we recommend starting at socket 0 and filling the sockets in numerical order: 1, 2, and 3. Use only HP DIMMs. For availability of DIMM upgrade kits for the NetServer LPr, check the web site at: http://www.hp.com/netserver/products/accessories/ Tools Required If you have to remove the LPr chassis from the rack, use Torx T25 driver. Refer to the last section of Chapter 9, "Removing the NetServer from the Rack." Use an anti-static service kit (3M™ 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. Installing Additional DIMMs 1. Log off all users. Back-up files. Follow instructions in your network operating system (NOS) documentation to gracefully shut down all networking software and applications. 2. Press the power switch on the HP NetServer's control panel when prompted by the operating system. 3. Disconnect the power cables and signal cables and, if necessary, label them to support reassembly. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
31
Chapter 5
Installing Additional Memory
Introduction
The NetServer LPr’s main memory is implemented with 5V SDRAM DIMMs
(Dual In-Line Memory Modules). The NetServer LPr ships with at least 64 MB
of main memory and supports up to 1 GB. Memory is available in the following
DIMM capacities: 64, 128, and 256 MB.
There are four DIMM sockets on the system board. See Figure 5-1 for socket
location. DIMMs may be installed in any combination in any socket. However,
we recommend starting at socket 0 and filling the sockets in numerical order: 1,
2, and 3.
Use only HP DIMMs. For availability of DIMM upgrade kits for the NetServer
LPr, check the web site at:
Tools Required
If you have to remove the LPr chassis from the rack, use Torx T25 driver. Refer
to the last section of Chapter 9, "Removing the NetServer from the Rack."
Use an anti-static service kit (3M
8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist strap.
Installing Additional DIMMs
1.
Log off all users. Back-up files. Follow instructions in your network
operating system (NOS) documentation to gracefully shut down all
networking software and applications.
2.
Press the power switch on the HP NetServer’s control panel when
prompted by the operating system.
3.
Disconnect the power cables and signal cables and, if necessary, label
them to support reassembly.