HP LH4r HP Netserver LPr Installation Guide - Page 64

Align the additional processor module over the secondary processor

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Chapter 8 Installing Additional Processors 2. Align the VRM card on the secondary VRM slot. Note that the component side should face towards the center of the enclosure like the VRM already installed. CAUTION Do not touch the components as you push the VRM card down into the socket. 3. Gently push the VRM down into the socket until it is seated completely. Make sure the VRM connector latch (see Figure 8-5) is raised to lock position. 4. Align the additional processor module over the secondary processor module slot so that the heat sink faces towards the center of the enclosure like the processor module already installed. 5. Gently push down on the additional processor module until it is fully seated. Figure 8-4. Installing the Processor Module and VRM on the System Board 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 8
Installing Additional Processors
56
2.
Align the VRM card on the secondary VRM slot. Note that the component
side should face towards the center of the enclosure like the VRM already
installed.
CAUTION
Do not touch the components as you push the VRM card
down into the socket.
3.
Gently push the VRM down into the socket until it is seated completely.
Make sure the VRM connector latch (see Figure 8-5) is raised to lock
position.
4.
Align the additional processor module over the secondary processor
module slot so that the heat sink faces towards the center of the enclosure
like the processor module already installed.
5.
Gently push down on the additional processor module until it is fully
seated.
Figure 8-4. Installing the Processor Module and VRM on the System Board